feeder

Hello, I am having trouble with our SM52. I slipped the suckers the other week on the chain and it was working perfectly before my week off the line on the control console said the papers were going in at perfect timing I had been running a job through without any issue. But on my week off it...

Hi All PM52 4 colour press. Running envelopes and press misdeeds and stops. Had many times before. Clear jam and start running again. Not this time! Press feed button and no suction. I have error code C30 on the console, but can’t find out what the error code is. Just lists as a feeder error.

Hello! We are having an issue with vaccuum's, when picking up a sheet of paper from the board, not releasing the sheet once in a while, causing a blockade before paper even reaches the drum (or front lay). It's happening above 3000 r.p.h., and usually with lighter sheets. Suckers doesn't...

hi, Has anyone had this problem, the sm102 machine does not allow the feeder to start? Regards.

Does anyone know what the sheet arrival timing should be on a 2008 CD102. I have checked the arrival and right as the sheet hits the headstops I am showing around 190°. The feeder is a preset plus and we have recently been having issues with getting sheets to run. When a sheet finally jams it...

Hi, I have gone through all the technical books I got with the machine, but I have not been successful in finding the details of the errors displayed on the feeder side of the machine. I have attached the details I received. Hope someone could help me out. Thanks, Charith

I have a QMDI-46 Pro. Normally when running the press, during a jam-up or if the machine pulls a double, the suckers will still have a grip on the next sheet that it is about to pull, so I can just clear the misfed sheet, turn the press back on to impression and away we go. However, now what...

Hi Everyone, I am experiencing an unusual problem in the delivery of my QMDI Classic since yesterday. We were experiencing some problem with the feeder all day where the paper was not feeding consistently and the press was stopping several times during runs even with the feeder settings...

Hi, I am having difficulty setting up the stream feeder on a 19x25 four color adast press. Any help would be greatly appreciated. Examples of where Rubber Wheels, chrome wheels, and where brush wheels should be in comparison to paper sheet. Thanks

Hi Folks, Ive been trying run polyester film A3 size on igen4 but the paper is jamming in the feeder sensor. its all setted up as a transparncy paper, thickness and so on. Does it ring any bells? Regards, Anderson Moreira

Even with my pile height set to minimum it seems my pile height is too high. Yesterday I was running some 50# bond (it was pretty flat) and it was a nightmare getting it to feed, constantly getting early sheets. It would raise the pile to about the middle of the 3 marks. I'm wondering if...

The plate in the feeder is moving down but not moving upwards. Machine is KBA Planeta supervariant. Plz reply soon.

I'm using an Astro env. feeder and have trouble with feeding doubles and alot of inconsistant feeding such as jams, having to stop and start alot . Just when i think i can speed press up another problem comes up. Can anyone coach me on how to set up correctly on this Ryobi Ha 3302?

Hi, We have been having the same problem with the feeder on our DI for about a year now, you can be feeding card one minute and then the pump just switches off for no reason and the press stays running. Another thing it does is the press can just stop, but the lights on the consoles are lit as...

What would you guess the value would be of an almost new Oversize High-Capacity Feeder for Docucolor 240/242/250/252/260? thanks!

:confused:I'm having serious problems with my feeder when I am running on uncoated paper from 70 gr/m². Or the feeder takes double papers or he doesn't transfer the papers right to the start of the printing groups. Is there anyone who has or had the same problems ? Kind regards,

FOR SALE: Oversize High-Capacity Feeder for Docucolor 240/242/250/252/260 Oversized High-Capacity Feeder. The OHCF’s air-assisted, robust feeder design enables the handling of 2,000 sheets* up to 13 x 19 in./SRA3 (64 – 300 g/m2/18 lb. bond – 110 lb. cover) coated and uncoated. This...

i m running new LS540 5 color+coater.our company try to cut cost by using bad shape of paper that is not uneven. with paper example 455GSM ,thickness around 0.48mm,812x456mm. with this papers ours feeder keep stop after 2nd paper but usually after 5 to 10 paper enter to the gripper. my...

The customer expectation document doesn't set much of an expectation for accurate registration within +/- 1.5mm lead edge and +/- 1.7 mm side edge. Am I reading this right that on a given sheet registration could be either + or - 1.5 mm for a total variance of 3mm offset in a run? This would...

Hey guys im new to this site my name is raymond. Ive been working in the print idustry for 3 years and i find myself on the back end of a 6 color komori lithorne 28". I seem to have alot of problems with keeping the sheets from turning at an angle and shuting off the press, weve tried everything...