Search results

What degree should the indeed wheels be set to touch 1997 SM 52- 2 Thanks

Running a 2001 SM 52. this last week started having movement issues with 2nd unit circumferential register. hairline adjustments may move much more than intended and takes too many sheets to recover on the fly so must shut down and start over with MR. These movements are only while press is...

Hey guys having an issue with compressor reaching kickout point. kicks off when starting press but cannot keep up, also only reaches 8.5 bar. does drain water when kicks off. I'm thinking leak somewhere in press but I cannot detect any or hear any leaks. Any ideas?

if anyone has a schematic of the grease gun for SM52 ,pointed nosel, I would appreciate it. Cannot figure how this gun goes together and make it work. Thanks in advance.

Good morning, Powered on SM 52 this am press will not move. everything is normal and press alarm rings but press will not engage. In creep mode the alarm rings and motor will click two times but not engage. Any help will be appreciated. Old School 52

Anyone have a diagram of a push pump Heidelberg grease pump. Found one but cant make it work maybe missing parts?? unable to fill it correctly.

Can conductivity be measured with a ppm meter. I'm using house water with conductivity of 175/200. At 3 oz per gallon of etch reading 375 after adding 6% alcohol, reading in ppm. It's not the same as measuring microhos??

New ink and dampener rollers 6 mths ago. Dampening problems ever since. Also company changed to Kodak on press developing plates and different ink supplier at the same time. Using S-3001 fount solution from bottcher. Only thing that hasn't changed. Thinking of changing to a tower product...

Good morning all, I am having issues setting the dampening system for short width jobs on this press. when setting the water pan roller the chrome the book implies that the crowned roller should be tightened until the bands disappear from ends of rollers. These are new rollers and these bands...

I am having problems with this compressor, DURR-TECHNIK, K15, runs all the time. This press is 15 years old and I have had many air leaks and repaired them in last couple years. This time is different, have all cabinets of except for gear side and cannot find any obvious leaks. I have been...

At what degree and tollerance are these rollers to be set. Also they are original and 12 years old, should they be replaced? Thanks for your help

I have constant need for resetting water rollers, new two monthes ago. will not maintain setting. crazy water swings dry and flooding. Not sure what manual means by centering the water chrome it does not look like it moves. When I sat the pan roller to it there is always a .25 band of water on...

Hi guys, My employer is looking for part # A1.184.0020. Its a cylinder / valve unit. I do believe the valve itself is fine but the electrical switch attached to the side of it is sticking. If anyone has a great way to clean the magnetic switch please let me know. Also if anyone has this...

I am having more timing issues on our SM 52. I dought that this press has ever timing adjuster at feeder checked, it may be just worn out. But let me start with something simpler, what degree should the infeed wheels touch down? Thanks

Good morning, This morning I turned power on to SM 52 and all power seemed ok but had a issue with pneumatic compressor . any ideas what I should do? We do not use press compressor we use an on site compressor which has had issues with water buildup during day. drained every day.

I see there are two setting areas but cannot find anything in book about which setting is first and second. top setting is on top in slot in the roller guard. second is along sides with a lock screw. any help is appreciated.

I am trying to set rollers on a quickmaster 2010. setting screw colors in manual do not correspond to this press. I have yellow - distributor setting Blue- distributor setting Red- Distributor setting silver-plate setting Orange- Plate setting Pink- Plate setting I do not have Purple or...

I have one unit, the second unit where the cylinder pressure does not work. When I turn press on it will twitch and that's it. The indicator on screen flashes constantly. On the other hand it will OCCASIONALLY move and set when programmed during setup. Computor problem or servo problem?

My press is not detecting the presence of the #2 washup machine. Any ideas of what may be wrong. I can program both units to wash but the second unit drops out when started. Also the yellow light is blinking indicating the #2 machine is missing. Thanks

Where can I find the sensor for back cylinder movement, its not moving.