Search results

Longshot here, i know this is not the most traveled forum these days...but worth a shot. I have an elderly IGEN 4, and I get this error constantly. Nothing seems to fix it forever. Change the belt, its good for a few days. it comes back. Do cleaning things, etacs, mob fixes it. but it returns...

no accompanying errors either. I'm totally lost lol did my usual, vacuum the cleaner brushes, clean etacs and mobs. mob and calibration an 951 both complete no issue, go to run, times out. restarted as well...

Came in this morning to a perplexing issue.... IGEN 4 is fine, no errors.... nothing. Starts up, gets going. BUt just as the sheet hits area 2, full death. No power anywhere. breakers all fine. just restart, it starts back up, then repeats. Nothing in the error log. Just random stuff. My...

last few weeks my color has been garbage. I let it go just babysat it. Called in the rescue squad this week. they fixed that-cleaning prob. now... Stacker doesnt steer correctly. Paper stays skewed, catches the edge of area 4. No real errors except. TE late to exit because of the edge catching...

EU Evaporator filter full. not sure what this error is saying....

All, cant remember if i ever made a thread on this... but its happened before... I just upped the fuser speed.... whats happening is, it LOOKS like the paper is entering the fuser slower than the pre fuser vacuum transport is pushing it in, and wrinkles up into the bottom of the oil tray...

got a phone call with that exact question. I know nothing about the specs. Am i a Test pilot again? anyone else do something that could be called "parchment"? lol

Like clockwork, we're now in the midwest fall, and almost instantly, its gone cold and dry. The last 5 months, The igen has been stacking smoothly... starting last week, I Get late to vgt exit 2 sensor and it Wont stack more than 1-200 sheets. when I pull paper off the cart, ZAAAP! I always end...

***SOLVED see second post. Pinscorotron grid to PR slope out of range. accompanied "log only" faults: 09-4414 VMC at minimum 09-4464 developer VMAG at maximum swapped pinscorotrons -no change.... cleaned etacs, cleaning brush...still wont run and wont pass 951. its a new one on me.

also has"too many registration marks" at the MOB sensors 6-3015 6-3016 reboot, and cycle the DFE it ran for awhile... now im dead. :/

Ive had this before... but never on normal paper.. usually only REALLY light gloss. Paper coming through the transfer 'bubbles' or 'bows up' in the middle at the trail edge as its exiting, not allowing transfer in a 0.5" x 2" spot ...I do not remember what we did when it happened before....lol...

entrance decurler home position fault. comes and goes.... coming more than going.... here's what iv'e been doing.... 1-clean sensor 2-reseat connectors for sensors(multiple) 3-hand advance decurler cam shaft(not sure actual term) 4-reseat connector for decurler motor 5-reboot. if im IN...

software reload, followed by a connector loose on reg board.... few days down off and on. came back after the latter, absolutely will not run my daily 50 offset paper. Sticks and rolls up OB corner.. "late to fuser exit" runs card and postcard stock fantastically... It's quite seriously making...

my Igen4 started giving me 9-1100's out of nowhere... so. restart, clean everything... cleaner,etacs etc... wont pass 951. So restart again comes back with 06-4201. something to do with ROS? reboot full with power off... now i'm not getting the board status page... just "software initializing"...

Been dealing with this off and on for a while... thought id look deeper into it. jams with "late to vgt 2 exit" 11-5510. its 14x18 55# offset paper. (its what I use almost exclusively) Stacker runs fine, sensors are clean....test ok. belts are fine. (i rebuilt the vgt last year or 2 i think)...

OK. ongoing, but not a dealbreaker problem. Im THINKING developer? Igen runs good for awhile... but after sitting, no cycle up, 9-1100 run 951, fail. but will sometimes print. Clean etacs, and patch generator, passes...then runs. FILTHY inside the cavity. Corotrons covered in Magenta...

Not much activity here these days..but ill throw this out there... We have original PDF's made for our big digital roll press. I do rework, samples, small packages. When I get these, and they have certain reds few blues... in particular 032U red. Igen makes a mess of it! Prints it as nearly...

Long weekend of kids' soccer, im exhausted... Had a rough monday morning of communication and power supply faults... got through it, breaker off reboots. came back got excited, now this.... xpe-09-3022 "no belt hole signal at the marker" never heard of this one... it was running fine before...

inboard ETACS LED Out of range. Ive cleaned them, will occasionally pass 951, then run for awhile but many times its this error. if I let it sit too long, it wont cycle up. 9-1100.... so the cycle begins again. got a 9-3110 once. Tried: new belt, pre clean corotron, random cleaning, checking...

about ten of them. all say missing 36v. plus inline spectrophotometer fault. cant get past it...ideas?