Search results

2004 Heidelberg SM 74-8 P5, CP2000 Modular Fully automatic perfector Dear all, i am having a problem when setting the machine to Perfector mode. The machine moves a little and stops before 0 position and engages Reversing drum lock lever. but the Reversing drum does not lock because its not in...

Hi, I'm facing the problem if SM74-8-ph machine is shutsown or power fail, upon restarting monitoring of reversing drum - storage drum syncronization is shown and have to reset perfection mode, put to straight. This happens if the machine was in perfector mode. This is fully automatic perfector...

Polar 78Xt is not booting. Display shows nothing. After power on the display is white which turns black gradually. Backgauge not moving and knife not moving. Main motor and blower runs. In CP board three green and 1 red led lights. Volts on power supply boards are ok, 24, 12, 5 DC. please suggest.

Hi I'm experiencing knife afterrun in Polar 78XT. I tried adjusting air gap of Magnetic clutch and brake. What should be the gap thickness? Any way to adjust sensor/encode position so clutch is disengaged a bit earlier. Thanks

Hi I'm having this Problem recently . Moinitoring of reversing drum - storage drum synchronization. The Machine is SM74 8 color 5PH. Previously it only appeared at power out, but now its appearing randomly. Sometime machine runs without problem for months and sometimes it appears 5-6 times a...

We tried to run the machine after long time of stoppage. The machine is not functioning. The machine displays '4000' which is speed and '0' at right side which is running counter and below that '120' which was set counter (It was setting when the machine was shut months ago). Unit selection is...

Hi, Heidelberg Stalhfolder 66 KD 2004 model is not booting. It is restarting while booting into operating menu. Display show Heidelberg Stalhfolder and number at lower left corner starts from 99 upto 20 while searching for dummy plug and connecting stations. It reboots after showing...

Hi we have been using this old machine since 4 years and about million impression die cut. Now the impression pressure needs to be set high (about 18-20) for the same job which ran perfectly at about 6 or 7 previously. The safety pin is not damaged and bushes also seems fine. What may be the...

I need wire connection diagram for SM74 Delivery Fan (ebm papst). The new fan has Red(+), Blue(-), White(Tach) and Purple (PWM) where as machine has White,Gray,Brown, Green. Need to know which wire connects to which Thanks

Hi Roland 201 single color machine is not running, no inching. No fault lights. All other functions are ok. Compressors, pile up down, damping all working but machine not running. Contactor are also not engaging. Any Ideas?.

Hi, can anyone tell me hardness of damping metering roller of QM 46 second unit. Thanks

SM 74 - 4, 2008 All safety locks/guards are shown actived. Only water chiller and computer Screen gets power. Pneumatic, Air Compressor, CPtronics Displays Unit Switchs Feeder, delivery nothing getting power. In Error menu "60" is displayed when opened error many, all the safty covers are shown...

I want to know how to Connect Polar 78 XT to Network for transferring CIP3 Data. What are the hardwares and softwares required. Polar-Mohr 78 XT with jogger & stack lift 2008

Hi, is it possible to link Heidelberg SM 74-4 2008 & Heidelberg Suprasetter A74 so that all the info from CTP be transferred to SM ? If so how? Thanks.

Hi, i want to know how easy to fit plate in MOV. Does it have easy plate system? Thanks in advance

Hi, I want to know what is the power required for SM52-4p low pile. Here we have 440 volts 3 phase. what will be the power of the machine in this voltage. Thanks

Can anyone tell me what are the features or advantage of CPC 1.04 over CPC 1.03

What does 'P3" in 'Heidelberg SM52-4-P3' means. What are the different features than SM52-4-P. Also what more features are there in CPC 1.04 than 1.03. Thanks in advance.

I wonder what are differences between Speedmaster 52-4 SE & Speedmaster 52-4 P execpt speed of 13000 and 15000. Can anyone differentiate more clearly.

What is differece between Auto Plate Loading & Semi-auto Plate loading. I'm planning for SM52-4 and wondering what is semi-auto plate. Do i have to manually clamp the plates or it fits automatically with a push of a button.