Search results

Anyone who has a Horizon BQ-440 Perfect Binder must have cover scoring please let me know. Hear from anyone soonest. Thanks.

Hi, I want to personally thank you for the help, by pointing out the sensor to clean, solve the Error 52. By the way do you sell used Horizon Vac 100 parts ?

Have a Horizon Vac 100 tower C error 152 ( see picture ) - manual says Pulse Error - Remedy is to check loading of the pulse encoder or the paper dust on the encoder. Can any forum member point out, if possible with picture, where the pulse encoder in a Horizon Vac 100 C tower is located...

Have an existing Vac 100a tower working ok but needed more pages to collate so bought a Vac 100m tower. After connecting the 2 towers, A tower on the left side M tower on the right side. I set up System Switches A tower Total 2 Order 1, M tower Total 2 Order 2. I then connected the Signal...

Just bought a Stahl VBF 2001 3 Knife Trimmer cannot seem to understand the controls, also need to know the Oil Grade required for central lubrication and also the Hydraulic Oil Grade required. The machine did not come with any manuals with it. See pictures below Hope any forum member can...

Have available Brand New Heidelberg EPROM board with part no. 00.785.0330/ EPM11 programmed SW 0.22.0 which is mated on top RGP3 board, tech made a mistake of ordering the board which was not defective in the first place. Have tested the board 100% guaranteed working. Email...

Have available Heidelberg RRM board with part no. 00.785.0026/03A which is mated on top RGP3 board, tech made a mistake of ordering the board which was not defective in the first place. Have tested the board 100% guaranteed working. Email: pressmachines@yahoo.com

Thanks

Just an update we finally found out what is causing the fault, its the small door at the operator side near the floor between the 2nd and 3rd unit thereis a sensor which should mate with each other, although it looks close it is not mated and aline with each other. So we just tied the sensors...

Please see picture of part ( picture 1 ). Also tech said he cannot exit this screen ( picture 2 ), which normally always can be done by pressing the green check button . Thanks. .

Thank you and appreciate your help. Please see attached crank picture and picture to show that the machine mechanically is in straight mode.

Have newly arrived 1999 SM 52 6P just arrived and installed. After switching on the press " Plausibility check of stored position of the perfector " and " Reset fault perfecting to straight " appears in the fault display. ( picture 1 ) The press is not ready to run. Mechanically the press is...

Have a RGP 3 main / mother board with part no. 00.785.0025/03B that needs to be replaced. I was offered a replacement board with part no. 00.785.0025/05 Just want to know if this is ok. My machine is a 1999 SM 52-6PH. Any input from forum members is highly appreciated. Thank you in advance.

Have a Horizon Vac 100c Collator with Feed Sensor error in all 10 bins, ( first picture ). Base on the maintenance section of the operation manual of the collator there is a need to clean the Feed Sensor of the collator (second picture). Based on the manual, I have cleaned all 10 Feed Sensors...

Can anyone refer me to a company or someone who can do repairs on Grafix IR Dryer GSTA Controller see attached first picture. The problem of the IR dryer is that the display just lights up ( see attached second picture) when you turn the main switch on the front of console but not showing any...

Picture where it is located. Thanks in advance

Can anyone share the Heidelberg Part no. of SM 74 pneumatic cylinder that is mated to the Blanket Cloth Washer Assembly. The Blanket Cloth Washer Assembly is installed on to the press and its mated to a small pneumatic cylinder with a pointed rod in the middle, when Blanket Cloth Washer...

I do not know if I am lucky or not but I have same controller model box which I think it come with another machine long time ago ( complete component inside ) but I do not know the condition if this is working or not unlike the one connected to the SM 74 right now which is working but no...

Thank you for your help. The problem started when it was still with the previous owner of the press even before I bought it. Can we assume that the screen display is still in working condition. Can you point out the part in inside control box that I need to check. I can take a picture of the...

Have a SM 74 which I just bought with a Grafix MS 250 IR dryer ( new year 1998 ). The IR dryer does worked, but the display just lights up and does not show anything else. Previous owner just turn on and off the the IR dryer using the on and off buttons ( upper left side ). Is the screen...