Search results

Hi Everyone, I am having trouble with the Technotrans on our 1998 SM102-8-P5 For a few weeks now, the Technotrans was not coming on regularly when the temperature rose to 11 degrees Celsius. Our set temperature is 10 degrees so the unit usually comes on at 11 degrees Celsius. In order to keep...

Hello Aadil, What or where is the REK please? Sorry if this sounds silly but I am not familiar with REK. Thank you! Shawn

Hello morrizc, I know this post is from a long time ago! I am experiencing the same problem on my SM102. How did you eventually resolve the problem? Please send me any information if you managed to find the cause and the remedy for this problem. Thank you in advance. Kind Regards Shawn...

Hello Matthew, I saw your reply to the above post regarding problems with a TECHNOTRANS issue and I read in the post that you are quite experienced with the finer details of the workings of TECHNOTRANS and ACLOSMART. We have a Heidelberg SM102-10-P5 equipped with TECHNOTRANS Beta C. The unit...

Sorry MeMo, Regarding the errors we encountered AFTER replacing the voltage detection module we found that there were 2 wires loose on the machine transformer. Immediately after we tightened the two contact lugs on the transformer, the errors went away. Fortunately this was a simple fix but...

Hello MeMo, Yes - fortunately we figured out the solution. The VOLTAGE DETECTION MODULE on the SLT Board was damaged due to excessive incoming voltage at our factory. We had switched on the press over a weekend when other factories around us were closed. The incoming voltage went up to 440V...

If all these errors showed up suddenly together, it is most likely that you have a communication problem between the press and the CP2000 console. Have you checked all cables, plugs and pc boards in the CP200 cabinet? Try to unplug and reseat all plugs and ribbon cables inside the cabinet first...

Good Day Majdi, Did all of these errors suddenly appear at once? When you restart the machine several times to get it working, do these errors go away or are the errors still there? Regards Shawn

Hi PWInc, We are also experiencing a problem with the clamp on our Polar 137. The clamp does not move when the foot pedal is depressed. We can hear a sound coming from the hydraulics but no movement. However, when we press the buttons to cut, the clamp comes down with the knife. So it...

Hi There! I have been following your posts regarding the clamp issue on your Polar machine. I am experiencing the same issue on our Polar 137 ED. I only read your posts now so I have not checked for leaks as yet - will do that tomorrow. Have you had any luck with fixing your problem as yet...

Hello Koening, I have been reading your detailed reply to USA CUSTOM PAD regarding the problems they are / were having with their Hydraulic system on their Polar machine. I am hoping you are able to assist us with our Polar 137 ED AUTOTRIM. We have recently purchased this machine and upon...

Hi All, We have recently installed a Polar 137 ED AUTOTRIM with a Transomat loader and off loader. Unfortunately, we are experiencing 2 errors viz. 1. Clamp not being activated by foot pedal. When the pedal is depressed, we can hear the motor that operates the clamp running but no action...

Hi All, We are currently finishing up the installation of a 2001 Heidelberg SM102-10-P5 Our incoming voltage to the press is set at 380V through the use of a LINEAR VOLTAGE REGULATOR. We had a problem a few weeks ago when the voltage in our building went up to 420V over a weekend when...

Thank you turbotom. Appreciate the advice

Hello Celso, I am experiencing the same errors on a newly installed 2001 SM102-10-P5 machine. The exact same errors popped up today. "I narrowed it down to the current and voltage detection module, GNT6029183P1" How did you confirm that this module was the cause of the errors? Did you...

Hello Joe, In response to your questions above, I would like some advice on the following please: (we are running two Heidelberg Speedmasters - a 10 Colour and an 8 Colour - Our Technotrans is set to run at 10 degrees Celcius 1. What is the ideal ratio of Fountain Solution: IPA : Fresh Water ...

Thank you Joe!

Hi All, We have just purchased a Heidelberg press that is fitted with Black Perfect Plus perfecting jackets. The jackets are in very good condition and I would like to ask for advice on what chemical/s we should use to clean these jackets without doing any damage to the jackets. Any advice...

Hello All, I am experiencing ERROR 653 on my Polar 115ED Guillotine I have read here on this forum and elsewhere on the internet that this error is associated with the proximity sensor pictured above - B341 Proximity Sensor. Can anyone assist with a Part No. for this sensor please. I cannot...

Hello Adil, I am getting ERROR 653 on my Polar 115 ED I have read on the forum and elsewhere on the internet that the problem is usually related to the B341 SENSOR I have managed to locate the B341 SENSOR underneath the table. Can you tell me where to find the actual PART NUMBER of this...