Search results

I have gotten the press fixed but my timing is slightly off as the Suction (paper) is on at the Run position. can anyone please advise on how to set the timing for this area. Thanks

Does anyone know what could be causing my machine to be in stop mode as 2 of the five light are not coming on in the perfecting unit as everything seem to check out, any electrical diagram would help as we got this unit used. Thanks for your help

Thanks for your advice, I am praying... Is there any chance you have a picture of the page of the service manual of the area we are talking about.

Please advise as my operator has made the star wheel bar loose and it got caught and the delivery grippers are not straight anymore as the chain delivery can be seen as twisted as right side chain is more advanced into machine about 3' away from the other side. I don't want to loose anything...

someone Please help, we have been supplying printed material to banks that has them printed with Drop Out Inks that is to guide the customers to write in a particular area but will not be show on the scanned copy. we need to have a tester or some error free method to check the density so that...

I really need assistance on this ink, please anyone have any suggestions.. Thanks

Good morning Sir, success. thanks so much for your guidance. The orange light wasn't working so I took a VOM and checked the bulb and noticed an open circuit so I took the orange one from the CE control from the front of the cutter and after putting that as a replacement the cutter is working. I...

Indicator light (5/8" diameter Orange light) on the right side is OFF, when one cut button is pressed the three light on the left goes out while three remains on. When I press two cut buttons simultaneously no brief blinking just 3 light goes out with no movements of either Clamp nor Blade...

Help, We have a Polar 90CE serial Nr.412281 that is experiencing problems as it was cycling sometimes, now it has stopped. We were told to that the #8A and #9 Board was bad so we purchased these which wasn't cheap and after putting them in it is still not functioning. A technician is saying it...

Please assist in advising where I can source Black carbonizing ink in small quantity such as 5 kilos as I have a unusual request. India is too problematic, I need a US source rush. any assistance is greatly appreciated. Thanks

I really need one for the GTO press that we have in our Plant. If you are familiar with it can you give me the measurement of the size of it, or can you guide me where I can purchase one so that we can tweak our presses to run more efficiently. We are in Belize Central America. we are very...

site of heidelberg zero tool http://www.aliexpress.com/item-img/heidelberg-adjusting-zero-tools-haidelberg-repairs-tools-heidelberg-tools/1467696728.html

Good day, this photo is the only image of the tool I believe I need to identify or point the "0" point for us to use the graduated disc on our GTO52 press. I really need to know the measurement from the point to the centre of the plug beside the Blanket/ Impression cylinder on the Drive side...

the tool is the one that is placed into a hole mounted on the D.Side of the GTO close to the Impression cylinder. This will be used to point to the '0' inscribed on the Imp. cylinder before securing the Graduation Scale mounted on the outside of the press on the D. side which is used to...

Please assist, I have gotten a Graduated disk but cannot locate a WLM 113 gauge block. can any technician post a picture for me and can we correspond so that I can get some advice on its use....thanks

need to contact attention exheidmech, my email is lbalderamos@santiagocastilloltd.com. please contact as I need to establish more assistance. thanks. sorry but I just cant seem to find out how to PM contacts.

Please advise on a program that we can use to number sequentially in various colours on Linoprint C751 digital Press. We have tried the program NUMBERING MACHINE PRO but it doesn't print the PDF image and number at the same time, either one or the other prints.

Greetings, please advise on best way to change transfer gripper needle bearings NK18/16ASR1 on our 1998 GTO 52-2-P. The 2 sides of the shaft is moving so both the bearings are bad, I guess the overuse of wash down solution that has fallen on the shaft over the years has taken its toll. We have...