Search results

Found one, but thanks for the reply

AB dick Specs say 1,300 lbs with T head

I just bought a Rosback Model 220 True Line Perforator at an auction and it is a little rusty. I am in need of an operators manual and parts list, so i can get this up and running. I would prefer a PDF that you could email me, but beggars can't be choosy I will pay for copies and shipping if...

If your still looking! Log onto wirebids.com they have at least 1 auction a month you can pick up a ryobi 3302 and platemaker for less than $5000

Lantz whats your email and i'll send you service manual, Parts manual and electrical manual in pdf.

Hey Ziggy check out http://www.wirebids.com/ if no auction up yet Call:Boggs Graphics - (440) 564-9675 Ask for Chris or Jack and let them know what you are looking for, they just had one on the auction that ended on the 8th Boggs Graphics Equipment LLC 9988 Kinsman Road Novelty, OH 44072...

Still Looking

Bump;

I have a Multigraphics SP 990EI giving me Error Code 4 Error in Voltage Compensation of Exposure Time What do i need to fix this problem? I have another Platemaker i bought for parts. I have called all the graphics Dealers in the Cleveland Ohio Area and there are no techs for this machine.I...

Thanks Ryobiserviceman I was checking for power with one of those buzzing light up probes, When i checked with a meter i was only getting 32 volts from one of the legs. I borrowed a switch from another printers parts press and it did the trick. Thanks again Don

Went to start up today and all was good for about 30 seconds, and then no power no lights no fan. I have 220 volts at the plug in, When i turn on main switch there is nothing,usually the fan would start. I checked the main switch and it has power when turned on. Is there a main fuse i'm missing...

Ziggy Sticky is not a pressman and he's never run process before, so he had better have something to line up to. He's not going to use a densitometer to read values, it would just be good for him to keep his ink even and have someplace to start registering to. I've been running presses since...

Hey Sticky when you get your film strip it into your masking sheets, Line all 4 negs to the same ruled line on the masking sheet I asume you are going to run color bars so make sure those are cut out of the masking sheet along with your crop marks. if you dont print the color bars or crops you...

Try loosening the bottom bolt, It is you plate to blanket pressure. You should see a slight bounce of that bottom bar as you feed paper and the press go's on impression. also use some WD 40 and spray all your pivot points on that assembly in case it is gummed up with dry grease since you haven't...

I talked to XPress today and they said they never received an Email. Try this Email, it is the girl in prepress that outputs film. lea.annc@x-pressprinting.com or call them. 800-217-4263 or 440-951-8848 I told them to expect an email

I use a company in Ohio, they could make film from your files or film and plates for your 3302. They output film for most of the small shops in my area and are very reasonable with their prices, I'm sure they would mail to you. Look them up on the web at http://www.x-pressprinting.com or call...

I use a company in Ohio, they could make film from your files or film and plates for your 3302. They output film for most of the small shops in my area and are very reasonable with their prices, I'm sure they would mail to you. Look them up on the web at http://www.x-pressprinting.com or call...

If anybody needs them i have the service, electrical & Parts Manuals on 1 PDF. give me an email address and i'll send them

See The post about E3 he gives part # from sunx gxl-n12f I found on ebay for $19.95 here is the link info http://www.ebay.com/itm/Sunx-GXL-N12FB-P-PROXIMITY-SENSOR-NPN-GXL-N12F-/231115452188?pt=LH_DefaultDomain_0&hash=item35cf8def1c

E4 is the Timing Switch between 130 degrees & 220 degrees. try cleaning the sensor