Recent Activity
Activity stream for all registered members at Color Printing Forum.
-
elhamid replied to the thread Feeder block Offset roland 700.
This is a malfunction on the roland 700 offset at the loader table level blocking up and down. And error displayed on the console screen...
Jun 4, 2023 at 1:21 PM -
ED SMITH posted a new thread.
DryStar 3000 Combination/ Coating SM/CD 102 Plus - #90 ERROR in Dryer
Our DryStar 3000 Combination/ Coating SM/CD 102 Plus IR dryer is experiencing a #90 fault. Can anyone guide me to the source of the...
Forum: Heidelberg Printing Presses
Jun 4, 2023 at 12:29 PM -
Michaelsh posted a new thread.
Cp2000 got stuck
The software gets stuck in this mode, an idea for a solution? [ATTACH] Thanks https://youtube.com/shorts/le9F1D8NKVI?feature=share
Forum: Heidelberg Printing Presses
Jun 4, 2023 at 11:57 AM -
Sandeep kumar replied to the thread Feeder block Offset roland 700.
Not able to understand what you wrote
Jun 4, 2023 at 10:37 AM -
elhamid replied to the thread Feeder block Offset roland 700.
(attempt to translate) 134653 battery (?) on the battery (?) door plate (?) too heavy proceed to zeroing controller synchronize machine...
Jun 4, 2023 at 9:59 AM -
Sandeep kumar replied to the thread Feeder block Offset roland 700.
Send me some error picture
Jun 4, 2023 at 6:32 AM -
matthias76 replied to the thread How to do Zero key Setting in En29.
Dont know the machine. I'll do it on GL 40 like this: Choose zero position in pqc. There have nothing to be selected when adjust zero...
Jun 4, 2023 at 4:17 AM -
Martin Mueller replied to the thread Presspercent values change when ppf is loaded into the press.
Hi Camilo, I am happy to see, that you have got PPC in the meantime. There is another way to get your CIP3 values closer to the...
Jun 4, 2023 at 3:14 AM -
Adil replied to the thread sm74-2p problem.
on the X11 sheet, pin number 1 is mentioned on the right and it is from there that you can start calculating from right to left. you...
Jun 3, 2023 at 5:36 PM -
elhamid posted a new thread.
Feeder block Offset roland 700
Feeder commands are locked and console screen displays error 134653
Forum: Man Roland Printing Presses
Jun 3, 2023 at 5:11 PM -
DORIL CASTILLO attached a file to the thread sm74-2p problem.
Mr. Adil, thank you for your recommendation on the reset through X11. I send you a photo to help me identify pins 9-10 and 11-12....
Jun 3, 2023 at 4:20 PM
-
CHOCK replied to the thread Polar 78 x Display.
Hi sir You must test in the 3 PCB ; A) 1) kc +24Vdc 2) DAK output 350V for backlight 3) LCD / PLASMA /TFT Display 350 Vdc of...
Jun 3, 2023 at 1:53 PM -
Adil replied to the thread sm74-2p problem.
Remember at the same time . Put jumber on 9_10 and 11_12
Jun 3, 2023 at 1:04 PM -
Adil replied to the thread sm74-2p problem.
Please sir do that and your issue will be done Switch off the machine ،do this procedure for 30 seconde carefully and switch on the...
Jun 3, 2023 at 1:04 PM -
OkiTech replied to the thread Convert your Xante Impressia in to EN/PRES.
Here is different theory: if you install new drum and peoblem goes away and then comes back after a while, it may not be over supply but...
Jun 3, 2023 at 12:57 PM