Polar 66 No Boot

[AOD_Daggs]

So I've got a Polar 66 that one day when we came in in the morning, it just will not boot up. When you turn the main power switch on, the display lights up and immediately displays the Polar logo. It stays like that forever and will not do anything at all. No error messages, no beeps, nothing. I've tested all buttons on the touch pad with a multi-meter, non are "pressed". I've re-seated all boards and connections. My guess is that a board might be bad. My guess is the one in the middle (SK66 250586/040181). Can anyone confirm this or have any other ideas? Maybe which board could be the only one that could cause this? Any help would be greatly appreciated. Thanks!

 

[Coloured paper]

Hi!

It is for sure not a broken SK board. The board SK is just controlling the cut sequence.
Let us start from the beginning.
Let’s assume you have a 66 with a 5.5” monochrome display made before 2012.
When you switch on the machine the key board should give you one beep. If you do not have this beep the computer inside the keyboard will not start and the display will not work.
The first check would be the power supply. At the keyboard you have a green plug X500. If you measure between pin 1 and pin 4 you have to have 5.05 to 5.15 Volt d. c.
At the keyboard you have as well a green LED named V1 this LED should flash with a sequence of 1 Hz.

Coloured paper

 

[AOD_Daggs]

Hi Coloured Paper,

Thank you for your response.
When I switch machine on, I get 1 beep, then it displays the Polar logo. I do have the green LED flashing (it is labeled Aktiv), red is solid and "test" LED is not lit. I measured voltage at the keyboard, it was 4.98 vdc. I then adjusted voltage on the power supply, I now have 5.15 vdc. Still the same problem, just stays on the Polar logo and will not boot beyond that.

 

[Coloured paper]

The Next step is the communication between the keyboard computer and the board CP in the electric cabinet.
Therefor the machine has a small cable from the little flat green plug X503 at the keyboard to the upper connector X3 at the front side of the board CP (right board).
If the cable is okay you may change the keyboard of the CP board. I would start with the keyboard.

Coloured paper

 

[AOD_Daggs]

The cable tested good. I notice that the board CP that you spoke of has a 3.6v battery onboard. This battery is reading 0.5v. Could this cause my issue? I replaced the keyboard about 1 year ago.

 

[Coloured paper]

If the battery is off, the CP board is losing all memorized information’s. The cutting programm’s are gone, every morning you have to do a reference run, etc.
But the machine works (after all initialization) like it should. After switching off, all memory is gone again and it starts from the beginning.
In other words it is not the battery.

The battery should have at least 3 V d. c.
A normal electrician cannot solder the cable to a battery. The temperature would be much too hot.

Coloured paper

PS.: Is the keyboard still under warranty? Where do got it from?

 

[AOD_Daggs]

I figured that was the case, I guess I'm just digging for an inexpensive fix.
I will check into the warranty tomorrow, we did not buy direct from Hiedelberg. I believe it may have been a refurbished board. We purchased it from DEMERS PARTS INTERNATIONAL. They are an aftermarket Polar supplier.

 

[Coloured paper]

I fit would have been Heidelberg I could help. Sorry!

 

[AOD_Daggs]

Well at least we got it narrowed down to one of the two boards. Thank you for all of your help!

 

[PANSOL]

hi, i have a new board Polar 66 cutter 047914 for sale, price eur 600 , let me know, pansol,add,cytanet.com.cy

 

[PANSOL]

Polar 66 card 047914 for sale 600 eur, polar SAP ID.042013 eur 450

 

[Dinca Razvan]

Hello,

I have the same problem with my Polar 66, do you have fix your problem ?
The machine start to block if I used the button from the front pannel, now after 6 month the machine colapse totaly, have you change the boards ? have you change to front panel ?

 

[Dinca Razvan]

Hello,

I need to buy a POLAR 66 Board CP4 for my Polar 66 from 1998.


Best regards,
Dinca Razvan
0040 722 510 712
office@grafart.ro

 

[CHOCK]

Go to http://spareparts.market/parts-for-post-press-machines

 

[Dinca Razvan]

Thank you,

I was there, but NOTHING,

The BOARD that I need is 45193R CP4 card with software V3.0.8cpl for POLAR 66

Razvan Dinca

 

[Soso]

i have same problem on polar 66 2017 CP6 . it has problem verifying checksum what can i do?

 

[CHOCK]

Hi Sir

You Have 2 option:

1) Baumfolder in USA.
2) Polar Moht in Germany.

 

[Soso]

can i find somewhere booth file to reinstall in board? i can do this by myself.

 

[CHOCK]

No sir:
Only if you have some friend or colleagues.

The best idea, is NOT waste time, go the company, that i did mentioned before.