M-offset type 53 2003-03 le moteur principal ne tourne pas

[BALAS]

all the security are good, the machine shows no default, but when you support the power button on the screen I see that the machine has started, but the central engine is not running, turn the fan, the compressor is running, the vacuum pump is running, all other engines except the big DC motor.

 

[xfactor printing]

I tried to translate this to english, hopefully not too far off.

When I press the power button I see on the screen the start button is activated and even turn, but the central engine is not running

 

[BALAS]

yes

 

[PressmoversUKEngineer]

Si vous préférez communiquer en Français, s'il vous plaît n'hésitez pas. Y a-t-il des codes d'erreur sur les tests de l'init et dyn

 

[BALAS]

oui je te donne comment il affiche sur l'ecran
SPK------ 000F
EAK-13----6FFF
EAK-01------7FFC
EAK-02----7FFE
SEK---FFFF
HAK-----02----FFF1
HAK-01-------7FEF
DSK-7FFD

 

[wunmi-50]

Hi,
Did you get these errors from Initest or Dynamic test? The EAK boards are the same and can be interchanged to localise the fault. Has this been properly done without missing out or misplacing one of them?.
Pls note that these exercise should only be carried out by qualified personel. Good Luck.
Wunmi-50.

 

[BALAS]

voici tous les codes que affiche la machine indiquer moi la panne :
les lettres en majuscule veux dire la ou la machine flash le code sur l’écran

dyn-test-1
rek2----ffff spk----ffff

esk1----ffff esk2-----ffff

resk1----7FFE reck3-----ffff
srk-----ffff svt -----ffff
sdn-1/2----ffff slt-con----ffff
hwi----ffff mot----ffff

dyn-test-2
ntk-la-----ffff ntk-ree ----ffff
ntk eaey----ffff ntk-brx ----ffff
ntk-haex-----ffff

dyn-test-3 spo spu
eak-11---ffff ff ff
eak-12---ffff ff ff
eak-13---ffff ff ff
eak-15---ffff ff ff
eak-01---ffff ff ff
eak-02---ffff ff ff

dyn-test-4 spo spu
eak-3---ffff ff ff
eak-4---ffff ff ff
eak-5---ffff ff ff
eak-6---ffff ff ff
eak-7---ffff ff ff
eak-8---ffff ff ff

dyn-test-7
hak-01----ffff 7FEF ffff
hak-02----ffff ffff ffff
hak-03----ffff ffff ffff
hak-04----ffff ffff ffff
hak-05----ffff ffff ffff

dyn-test-8
hak-06----ffff 7FEF ffff
hak-07----ffff ffff ffff
hak-08----ffff ffff ffff
hak-09----ffff ffff ffff
hak-10----ffff ffff ffff

dyn-test-11
mid-11----ffff did-12----ffff
hakx----fff haky-----ffff
dsk----ffff pud-----ffff
cpcrek1----ffff cpcrek2---ffff

dyn-test-12
ssk1
§1----ffff
,
,meme information jusqu'au numero §16
,
§16-----ffff


INIT_TEST 1 t=0
rek2----1fff spk------000F
rek1----7fff esk2----0000
rek1----0000 rek3 ----0000
srk------0000 svt-----0000
sbm-1/2----0000 svt-com----0000

INIT TES2 t=0
ntk-la ---0000 ntk-ree----0000
ntk eaex---0000 ntk haex----0000

INIT TES3 t=0

dyn-test-3 spo spu
eak-11---ffff ff ff
eak-12---7fff ff ff
eak-13---6FFD ff ff
eak-15---ffff ff ff
eak-01---7FFC ff ff
eak-02---7FFE ff ff

INIT TEST 4 spo spu
eak-3---0000 00 00
eak-4---0000 00 00
eak-5---0000 00 00
eak-6---0000 00 00
eak-7---0000 00 00
eak-8---0000 00 00
SEK FFFF

VOICI QUELQUE CODE QUE LA MACHINE AFFICHE SUR L'ECRAN.MERCI DE M'AIDER?????? TOUT SEMBLE ETRE NORMALE MAIS LE MOTEUR CENTRAL NE DÉMARRE MALGRÉ QUE LE VOYANT DÉMARRAGE EST ALLUMER

 

[wunmi-50]

Hi BALAS,
The errors you need to troubleshoot this fault are those on Initest and Dynamic test at time t=0 and it should be taken when you have just switched on the machine and before inching or rumnning the press.
Pls check and confirm that the power supply boards NTK having green LEDs on the pcb racks are on/lighting.
Are yu sure the mains power suppply to machine is appropriately correct.?;Check the fuses.
Wunmi-50.

 

[BALAS]

toutes les LED vertes des carte sont allumée, j'ai contrôlé tous les fusibles tout est OK, même l'alimentation du secteur, sur l’écran y a aucun défaut, quand j'appuis marche le moteur ne tourne pas mais sur l’écran tu contacte que la machine est en marche,

 

[BALAS]

aidez moi

 

[wunmi-50]

Hi,
Switch your machine on again and copy what is on the display on INITt=0TEST and on Dynamic Test all for time t=0 and post it to start afresh.
wunmi.

 

[BALAS]

voici tous les codes que affiche la machine indiquer moi la panne :
les lettres en majuscule veux dire la ou la machine flash le code sur l’écran

dyn-test-1
rek2----ffff spk----ffff
esk1----ffff esk2-----ffff
resk1----7FFE reck3-----ffff
srk-----ffff svt -----ffff
sdn-1/2----ffff slt-con----ffff
hwi----ffff mot----ffff

dyn-test-2
ntk-la-----ffff ntk-ree ----ffff
ntk eaey----ffff ntk-brx ----ffff
ntk-haex-----ffff

dyn-test-3 spo spu
eak-11---ffff ff ff
eak-12---ffff ff ff
eak-13---ffff ff ff
eak-15---ffff ff ff
eak-01---ffff ff ff
eak-02---ffff ff ff

dyn-test-4 spo spu
eak-3---ffff ff ff
eak-4---ffff ff ff
eak-5---ffff ff ff
eak-6---ffff ff ff
eak-7---ffff ff ff
eak-8---ffff ff ff

dyn-test-7
hak-01----ffff 7FEF ffff
hak-02----ffff ffff ffff
hak-03----ffff ffff ffff
hak-04----ffff ffff ffff
hak-05----ffff ffff ffff

dyn-test-8
hak-06----ffff 7FEF ffff
hak-07----ffff ffff ffff
hak-08----ffff ffff ffff
hak-09----ffff ffff ffff
hak-10----ffff ffff ffff

dyn-test-11
mid-11----ffff did-12----ffff
hakx----fff haky-----ffff
dsk----ffff pud-----ffff
cpcrek1----ffff cpcrek2---ffff

dyn-test-12
ssk1
§1----ffff
,
,meme information jusqu'au numero §16
,
§16-----ffff


INIT_TEST 1 t=0
rek2----1fff spk------000F
rek1----7fff esk2----0000
rek1----0000 rek3 ----0000
srk------0000 svt-----0000
sbm-1/2----0000 svt-com----0000

INIT TES2 t=0
ntk-la ---0000 ntk-ree----0000
ntk eaex---0000 ntk haex----0000

INIT TES3 t=0

dyn-test-3 spo spu
eak-11---ffff ff ff
eak-12---7fff ff ff
eak-13---6FFD ff ff
eak-15---ffff ff ff
eak-01---7FFC ff ff
eak-02---7FFE ff ff

INIT TEST 4 spo spu
eak-3---0000 00 00
eak-4---0000 00 00
eak-5---0000 00 00
eak-6---0000 00 00
eak-7---0000 00 00
eak-8---0000 00 00
SEK FFFF

VOICI QUELQUE CODE QUE LA MACHINE AFFICHE SUR L'ECRAN.MERCI DE M'AIDER?????? TOUT SEMBLE ETRE NORMALE MAIS LE MOTEUR CENTRAL NE DÉMARRE MALGRÉ QUE LE VOYANT DÉMARRAGE EST ALLUMER

 

[wunmi-50]

Hi,
Do you have these errors on INIt=0TEST-1
rek1 0000
EAk13 6FFF
EAK01 7FFC
EAK02 7FFE
If yes,you may have a defective rekw board.FR THE EAKs you will need a technician to swap them round and find out those that have defects.
Cnfirm the above and lets kk

 

[superteto]

contact me : ercupa@netscape.net

superteto