clamp

I have an IDEAL 5221-90 gullotine paper cutter. Yesterday it was working fine but today as the clamp came down, it refused to go up. When i press the button all it makes is a clack sound and that's it. I have no idea where the electrical panel is located as i read somewhere on the forum that...

So I have only been able to find solutions for the clamp/knife being stuck down, but I am stumped on this one. Ideal 4850-95 EP took off electric cover, K1 and K3 both go down when buttons are hit, but nothing happens. when I manually hit K2, there is a terrible whirring sound, like the motor...

Dears, Suddenly, the clamp of my Polar emc 137 stops moving up Has anyone faced this issue before? Best Regards

FOR SALE / EN VENTA SHOP-1 : / TIENDA-1: 1) 1994 Polar 115EMC -MON 2) 2000 Muller martini Presto Saddle Stitcher/ Grapadora de lomo Presto Muller martini 2000. 3)Stahl T-66 Folder (2 numbers) / Carpeta Stahl T-66 (2 números) 4) Sulby Single Clamp perfect binder / Carpeta perfecta Sulby...

hi everyone, i have problem with my ideal 5260 paper cutter. in process of cutting both clamp and blade stuck in down position. fuses seems to be ok, overload switches (blade drive/clamp drive/backgauge drive) stick out some 4~5mm so i'm not sure if it's ok (when pressed they return to same...

Hello, I have a polar 76 em My problem is: The clamp comes down so hard it bounces and when it returns it bounces even worse! The clamp does this with or without the pedal, so I don't think the pedal adjustments do anything. So to be clear if I just hold the cutting buttons the clamp will...

Hello every one, we`ve been having clamping problem lately, as clamp won`t go down with foot pedal, but works ok when cutting. we checked foot switches, both work ok. we decided its a hydraulic problem, removed the the whole valve block, took out everything, cleaned it, changed all...

Hello, I cut bundle of 500 paper length of 32 cm to 29.7.cm When the blade come down, the rest of the cut is moved to the left and went into the slot on the left side on surface of cutting. That block the knife. Then I pulled out the rest of the cut, and cut the paper to the end, but after...

Hello all - I recently replaced the disc brake on the blade motor of my Ideal Triumph 4850-95. Since the repair it seems to be traveling better on the trip down, however the only way I can get the clamp and blade to return to the top position is by opening the safety cover. It is not...

Hi All, Over the past year or so, our shop has been having trouble with one of our Eurocutter 1380 AD trimmers. It seems that the clamp loses pressure for a short time DURING the cut! This, of course, wrecks a lift of paper, and since we are a short-run shop often the whole job goes in the...

has anyone any tips on how to set the plate clamps on this press? i know they are very sensitive to set and that how they are set affects how the plate tensions aswell. Fit between the units is almost impossible to achieve now. we have a 1998 ryobi 525hx which is better to get to fit than the gx.

The center part of the plate clamp on our quickmaster 46 is frozen shut. Any suggestions on what our next step is? We are not sure if the whole clamp needs to be removed from the cylinder or not. Any help at all would be appreciated since our location requires us to fly a heidelberg mechanic up...

We have a gto 52-z alcolor and the operator has to put about .015 shim under the tail edge quick clamp. Is there an adjustment that we could do to the clamp so he does'nt have to shim it. I thought before I go out and buy a new clamp, maybe someone might of had the same problem. If so please let...