Search results

  1. Buying used Igen3

    you win LOL

  2. Buying used Igen3

    !!!

  3. Buying used Igen3

    find a used 4 over the 3!!!!!!! waaaaaaaay better machine! Our igen3 was a dog..the xerox tech was in everyday for months... we got upgraded /swapped like for like to a igen 4 LOL...check the #s..your used Igen 3 just may be my old nightmare LOL

  4. Manual impression on a QM 46

    special function 01 is h2o and spf 02 is ink roller (look on the inside of the door) then use the feeder table or delivery crank to turn the press Plate to blanket you use the dial on delivery upper left with a socket or red operator tool to adjust the pressure ...other then that there is...

  5. I HATE iGENS

    They can be stress full!! I am a 2 color press operator first ,digital 2nd..My problem with the igen.. is having to multitask while it runs LOL. While the Igen runs I am setting up other igen jobs ,or in the bindery,running other digital machines,folding cutting etc etc instead of standing...

  6. IGen 4 software glitch

    This is a strange one...some days we can run a job with front and back covers and some days we get a fault, when I release the job a message "not enough pages in document to support covers" pops up and I have to run the covers as a separate job and collate by hand:mad: running the latest and...

  7. Re-calibrating Qm46 Electronic Eye

    I talked to my tech friend 11-07 is the sheet getting stuck between the eye sensors There is NO adjusting the senser!!! Either there is a burr or dirt on one of them or it is too high or low or the angle is off !! a new plate is like $700 give Jim Lovely at independent press repair a call...

  8. Re-calibrating Qm46 Electronic Eye

    sorry but I dont know what the 11-07 is

  9. feeder problems on QM46

    you should be able to run it full speed with very few jams!! blast air at 6, suction at just under 4 with 0 -1side blast and the table just below the middle mark should be a good starting point. Also max out the sheet separator fingers. where are your forwarding wheels hitting the paper? Fold...

  10. Re-calibrating Qm46 Electronic Eye

    what is the error code? (Special Function 56 I believe )

  11. Re-calibrating Qm46 Electronic Eye

    not sure I am on the same page with you..which senser? The electronic eye on the feed is made to pop on and off for cleaning !!! It needs to sit flat and the spring clip holds it down ..if it is not in right or the spring clip is weak you will have problems as light gets in and triggers misfeeds

  12. Succesful Mailing Tabs and Wafer Seals for Xerox iGen 3/4 users

    NO!!

  13. proof 1 then run the job and colors dont match!!

    I was wondering if anyone else has run into this one Do 1 proof..check color,reg. etc.,30 seconds later Release the job and the color is not a match too the proof!!! does not matter what stock ? New PR belt,new fuser roll,.pres. set at 14.5. New wire mods, grids etc etc no pattern or...

  14. magical mystery jams

    We had/have a similar issue...turns out that the doors dont stay closed...either give em a little kick closed everytime or use velcro

  15. Rislan Roller damaged by wash up blade

    LOL, I did that 12years ago....if you are able to print just leave it.

  16. image reg. set-up n

    Side 2 was printing skewed on 12x18 80lb gloss text...after I went a did the dco610 set up..pain in the arse x 3 ... the color registration is all messed up and I cant print anything but black...any help would usefull

  17. Rub-off on silk-coated stock

    Eating my words here!!! :( we have now joined the club with toner rubbing off......... on almost all stocks!!!!! 100 uncoated cover seems to be the worst!!!

  18. Quickmaster 46 Plate Issues

    to do it right you need a special tool/guage...other than that in a pinch it can be done on a flat surface if you know what your doing

  19. ab dick b/w print - ran out of patience and ideas, please help.

    I am not familiar with your press but printing is printing !I dont think spring water will help...try distilled water,and cut back on your fountain solution also maybe try varn aqua varnish #30

  20. Succesful Mailing Tabs and Wafer Seals for Xerox iGen 3/4 users

    me to ..info @arlingtonswifty.com
Back
Top