Search results

thanks for your response as it got me looking more in depth at the linkage and I concluded that when the unit arrived someone must have turned the impression of the numbering unit, and this move the linkage that control the arm which pushed the hole out of place for the numbering activation...

I have a PM52 that is printing ok but when the Numbering unit is installed, we note that the numbering unit doesn't go into impression. note the photo that when we press in lever it doesn't go in even after pressing it aggressively. what could be causing this to happen? please advise.

Thanks for your direction, what I would like to know is users perspective using this model as many are suggesting Screen 4600 but we are not only ;looking at double the investment cost but we really like to know operators experiences to make us make the best long term decision.

Please provide advice on this model CRON 3624 G+

Panther pro 46 Have a Panther running a Xitron Navigator GPS ver 9 RIP. was working as normal . Now the client cannot see the server and when we go direct from the server its telling us the scsi is missing, please advise. We have no Cd for Client but has for the server.

Morning to all, Please help. Our panther pro 46 is our work horse in our prepress but we have noticed that we put in a new film and the length of the file is shrunk about 1/2" but the width is accurate. Has anyone experienced anything like this before. please advise

We just invested in the P7000 CTP from Presstek using a Epson 7000 printer on the JT plates. Can anyone advise on using these plates on a Heidelberg GTOV Alcolor press. We disconnected the transition roller but we need advice also on getting the right calibration between plate making and press...

We did some more test and noticed that the voltage to our pump is 0 even as we run SP 3050 which is force toner fill, What controls or send voltage to these pumps? we did check another color and that one get the 24Vdc during the SP 3050. Can anyone please help!

Good day all, please advise what is the purpose of the hole that is identified in this Photo. Its the Toner Supply Sub Assembly Pump. we are experiencing a toner supply issue that the print had a reduced color due to toner shortage. we cleaned and checked the supply hose and allis clean but the...

Afternoon all, after getting the press working for a the last two weeks we noticed that the Cam Follower that controls the Segment Gear is worn and we will need to change. Since I jumped the gun the last time to undertake the removal of the Pincer bar I really would like advice on this to...

We have successfully installed it even though we know that to get a perfect fix we would need some professional tools. We have a service manual that was bought a few years ago and we followed it as much as possible to get it close as possible before reaming out a new tapered pin hole to get it...

Morning Sir, we had taken out the pincer gripper from our GTO52-2-P as it was dropping the paper in perfecting only as on straight the pressman had applied some urethane to accommodate the worn needle bearings. we have ordered but we had too many orders requiring the perfecting capabilities so...

Thanks for your advice as well as your observation. Please understand in Belize, training and certified individual are many times non existent so we having 30 to 40 years of success dealing with Heidelberg presses and undertake tasks that require professional advice. This gripper is not that...

Good day everyone, we had worn needle bearing on the holder on the pincer bearings which we replaced but I had only marked the Operator side as I haven't had any experience on this removal and after removal I noticed that there are two separate gears and I had only marked one. Now I am having...

Thanks, thanks to you all as we were able to confidently bypass the old compressor air tank and do a straight air supply without affecting the machine ability to shut off if the water level drops too low. we have noticed that a part of our problem lie in the fact that there is a lot of moisture...

Your advice sound great, I am not familiar with a low limit switch that you installed , can you advise on how to do this, and do you have photos to assist?

yes, we want to do that. please advise on how.

Image shows what we have now as we had taken the motor off some time ago and the outside compressor is attached by the hose marked by RED arrow, we can hear some air leakage from electrical switch marked by Yellow arrow.

Is there anyway that we can bypass the electricals on this press an run a compressor direct to the press as initially the motor on the compressor went bad so we connected a compressor line to the Air drum so that it pass through and the electrical on the press would sence the air pressure and...