Search results

What is the file size? May be you can use the Google Drive ?

Thank you !!! Can you send it by e-mail ? lvivltf@gmail.com

Thanks in advance My e-mail - lvivltf@gmail.com

Hi ! We are looking for one page of circuit diagram - unit +AD, page "Mains unit remote disconection" (Roland 705 3B - 1992). There are some photos of catalogue and a page we are looking for in the attachment. Thanks in advance for any help or information.

Hi Roland 705 3B (709 series). We have a new problem. On the second section, the plate cylinder mechanically moved by 4 degrees against the zero position of the cylinder ( after replacing the plate ). We have put it in the zero position. But after a few days, it moved again (by 2 degrees to...

Hi Drukman! There is a picture with rollers in the attachment. The rollers 11.4 and 11.5 are absent. We have only 402, 21 and 31 rollers. But they don't have the pressing springs. Which of those rollers I must to adjust ? PS The stripes appear only sometimes and on different printing sections...

Hooray !!!!! I have fix this problem (16-5-0-0-0 SPS: Uberdrehzahl Feuchtduktorantrieb DW 2) ! It was a driver (A381/2) for the Water Fountain Roller Main Drive (in the attachment). Thanks to all for your help !!! Have a nice day !

Hi ! I have a Service Training Elektronic .pdf file (Communication system). As I understand - I need a service set for testing fiber optic cable, SPS Loop and Process Loop. Were can we buy it and what price ? "Or wrong resistors" - you mean a resistor in HP adapter for fiber optic cable or...

Hi ! Today the errors with Prozess-Bus occurred again. There are a pictures of errors screen (prozess-bus) and status of moeller fiber optic equipment in the attachment. According a battery - all ok.

At the moment Roland is in normal working order. These errors are not stable. They occur unpredictably. I need to catch the moment of error and the status of the fiber optic equipment. Then I will send those photos. According to the batteries - I personally did not change them...

What inverter are you talking about ?

Moeller

Thanks for your reply. Of course I'll check fiber optics. I did not pay primary attention to these prozess-bus errors because they appear after this first error for some time (2-3 min). I thought they was a consequence of a basic error.

Thank you very much for your help. At first I replaced the motor and the sensor. Yesterday I replaced input card 7, DA converters 8 and 9, -A397 and -A383 but unfortunately got no results :( - there was alarm according DW2 again. (in the attachment). The water level completely covers the...

Hello We have the next error that occurs periodically only when the system loading (see attachment - first error). As I understand, NODE 9 is MABEG feeder. In this case, indication and control on feeder are not active. Can anyone help me find the source of the error ?

Thanks. I'll try it. Also I found the next block -A397 on a board -A383 (see the attachment). It transfer the signal from the dampening solution level sensor to card in slot 7. I'll try to replace them also

Hello ! The situation looks so: 1. I replaced the motors between section 2 and 4 (with magnet and speed sensor) 2. I replaced the dampening solution level sensor between section 2 and 4 If they are defective, a DW4 error should appear. But there is'nt any effects - the error is same (DW 2)...

Hi to everybody Sometimes we have the next problem on printing - stripes or waves (see the attachment). This is electrical or mechanical problem ? Where I can start looking to fix it ? Thanks to all

Thx ! I'll try to change this motor between the section 2 and other one. If the problem with this motor - the error will be at other DW. I think this is an easiest way ;)

Dear Drukman Are you talking about the M101 engine (photos in the attachment)?