Recent Content by presselectronics

  1. presselectronics
    Post

    Timing disc for degree the press is at

    This is normally caused by the Varicam or the absocoder failing. If the Varicam display goes blank, replace it. If the absocoder is hard to turn,...
    Post by: presselectronics, Mar 4, 2020 in forum: Komori Printing Presses
  2. presselectronics
    Post

    Main Press Running Detector

    The uU error is normal, if it does not require that you push the reset button on the alpha numeric keypad. As for the settings, they are usually...
    Post by: presselectronics, Sep 30, 2018 in forum: Komori Printing Presses
  3. presselectronics
    Post

    Main Press Running Detector

    Start failure error indicates the press is not running 10 seconds after start signal command. You can double check all the parameters on the...
    Post by: presselectronics, Sep 30, 2018 in forum: Komori Printing Presses
  4. presselectronics
    Post

    Main Press Running Detector

    First thing I would check are the main motor Amp fans, accessible from the feeder side of the main electrical cabinet. Make sure they are not...
    Post by: presselectronics, Sep 29, 2018 in forum: Komori Printing Presses
  5. presselectronics
    Post

    Komori Sprint GS 228

    Sounds like your main circuit breaker, the one you keep turning on and off, is failing. I'd order a replacement breaker before you damage...
    Post by: presselectronics, Sep 19, 2018 in forum: Komori Printing Presses
  6. presselectronics
    Post

    KMS connection to PQC-D II

    Moxa is just a brand name, like Advantech, used on a lot of Komori PCs for serial interfaces. KMS stands for Komori Monitoring System, and even if...
    Post by: presselectronics, Jul 23, 2018 in forum: Komori Printing Presses
  7. presselectronics
    Post

    KMS connection to PQC-D II

    PQC DII was not made by Komori, but by Toyo Denki. I've seen some creative attempts to download ink key profiles, via the magnetic card reader,...
    Post by: presselectronics, Jul 22, 2018 in forum: Komori Printing Presses
  8. presselectronics
    Post

    PDUC Error

    Communication problem with DUC system, controllers that convert analog to digital (from unit to the PQC) and digital to analog (from the PQC to...
    Post by: presselectronics, May 16, 2018 in forum: Komori Printing Presses
  9. presselectronics
    Post

    pqc problem

    With that vintage PQC, I would start with checking the power supplies for proper voltage out.
    Post by: presselectronics, Apr 28, 2018 in forum: Komori Printing Presses
  10. presselectronics
    Post

    Driver manual for Lithron impression motor

    I have never seen a drive manual for the PDU-215. Toyo Denki is not known for sharing proprietary information.
    Post by: presselectronics, Nov 1, 2017 in forum: Komori Printing Presses
  11. presselectronics
    Post

    Brush shift/S-charge AC motor

    My guess would be that the brush shifting motor's slowest speed is not slow enough. Sometimes the slowest speed was not slow enough to wash up...
    Post by: presselectronics, Nov 1, 2017 in forum: Komori Printing Presses
  12. presselectronics
    Post

    Driver manual for Lithron impression motor

    "I am having komori Lithron 4 colour 1995 model.i want a driver manual for impression on stepper motor.i have attached the photos. Any body having...
    Post by: presselectronics, Oct 31, 2017 in forum: Komori Printing Presses
  13. presselectronics
    Post

    Brush shift/S-charge AC motor

    Sorry, unlike the wound rotor motors on older presses, you cannot easily adapt a freq drive to this motor.
    Post by: presselectronics, Oct 31, 2017 in forum: Komori Printing Presses
  14. presselectronics
    Post

    KOMORI PQC-D II Power Detection Board

    "Does anyone have information about the Voltage Detection Board aka fault board" Board is located in DII type PQC. Problem normally is that it...
    Post by: presselectronics, Oct 31, 2017 in forum: Komori Printing Presses
  15. presselectronics
    Post

    L-520 Programable Controller Cards

    "Having trouble with programable controller cards that work my pan rollers. They error out randomly, then turn back on as i am looking at them for...
    Post by: presselectronics, Oct 31, 2017 in forum: Komori Printing Presses