Recent Content by CRocket

  1. CRocket
    Post

    Power supply question

    Ours too came with three installed. Shortly after install there was a problem with the power converters(this is why we had one on hand). Xerox let...
    Post by: CRocket, Feb 6, 2014 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  2. CRocket
    Post

    Power supply question

    Hey Milo, Hows it going? The replacement power supply was just moved from the origonal postition to the empty slot and is now working just fine....
    Post by: CRocket, Feb 6, 2014 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  3. CRocket
    Thread

    Power supply question

    This would be for the techs perusing the forum. We had an instance where the machine would begin its cycle up and immediately shut down with along...
    Thread by: CRocket, Feb 6, 2014, 7 replies, in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  4. CRocket
    Post

    I killed it.

    Gives us some insight to the possible cause. Thank you!
    Post by: CRocket, Jan 16, 2014 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  5. CRocket
    Post

    I killed it.

    Did you ever find what the remedy for this was? We are having the same problem, power supply went out, replaced and now doing the same again.
    Post by: CRocket, Jan 15, 2014 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  6. CRocket
    Post

    IGen4 side one skewing problem

    Check where the lower transport mounts near the feeders. We had one incorrectly installed and eventually it ended up bending the counter balance...
    Post by: CRocket, Dec 23, 2013 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  7. CRocket
    Post

    cyan streaks

    Are the streaks in the process direction? The spacing of the streaks looks like possibly the TAB assembly or the PR belt.
    Post by: CRocket, Sep 19, 2013 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  8. CRocket
    Post

    Fuser web not picking up all debris

    We run and Igen3 and had this issue in the past. Eventually the tech replaced the external heat rolls with an upgraded set that are covered in,...
    Post by: CRocket, Aug 9, 2013 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  9. CRocket
    Post

    1st Side Image Binding Edge

    On the LE of the stock, at times the TAB assembly will leave marks roughly the width of the plastic tabs. They appear as streaks or just small...
    Post by: CRocket, Jul 25, 2013 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  10. CRocket
    Post

    1st Side Image Binding Edge

    Do the markings appear evenly spaced?
    Post by: CRocket, Jul 24, 2013 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  11. CRocket
    Post

    looking for an used envelop making machines ( Automatic)

    If anyone still interested? http://rocketdirectmail.com/Converting_Equipment_List.pdf
    Post by: CRocket, Jul 2, 2013 in forum: Collator-Booklet Maker Systems
  12. CRocket
    Post

    Xpe-09-4113, xpe-09-1100

    Any tests that may lead us to this, as the possible source of our frustration?
    Post by: CRocket, Jun 25, 2013 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  13. CRocket
    Thread

    Xpe-09-4113, xpe-09-1100

    Ok guys have had a reoccuring problem causing a few late and sleepless nights. We are not on a service contract and been relying on community, our...
    Thread by: CRocket, Jun 24, 2013, 3 replies, in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses