Recent Content by CHOCK

  1. CHOCK
    Post

    QM46...power goes off when impression is engaged.

    Thanks You Sir. Welcome. Blessings.
    Post by: CHOCK, Apr 21, 2024 at 8:17 AM in forum: Heidelberg Printing Presses
  2. CHOCK
    Post

    QM46...power goes off when impression is engaged.

    Good Job, Sir. Blessings
    Post by: CHOCK, Apr 20, 2024 at 5:43 PM in forum: Heidelberg Printing Presses
  3. CHOCK
    Post

    Ryobi 512 error code 222

    Hi sir: Please make a Reset in the CPU board, normally , they have Small Button for to do it. Let see what will happen If the error persist, look...
    Post by: CHOCK, Apr 20, 2024 at 4:06 PM in forum: Ryobi Printing Presses
  4. CHOCK
    Post

    Feed table sensor led

    Hi Sir; I did instruct to you, to do many things, NO RESET!!! That was that I did recommend you , that you will do . OK. ¿ Try to interchange...
    Post by: CHOCK, Apr 19, 2024 in forum: Komori Printing Presses
  5. CHOCK
    Post

    Polar Guillotine Green belt tension is lose

    OK. Sir.
    Post by: CHOCK, Apr 18, 2024 in forum: Heidelberg Printing Presses
  6. CHOCK
    Post

    Muller Martini Presto RIMA Stacker

    Hi sir: You must use the operator manual for to program, or Also, contact , Muller Martini, and get the section for Service Assistance, for Help,...
    Post by: CHOCK, Apr 18, 2024 in forum: Book Binding
  7. CHOCK
    Post

    Error 15-01 on Heidelberg Printmaster 46-2 (Also Quickmaster)

    Hi sir: I had sick, with heart attack, from January 17 ,2024, and recently in recover, thank God feeling better. am Older Man with 71 years.!...
    Post by: CHOCK, Apr 18, 2024 in forum: Heidelberg Printing Presses
  8. CHOCK
    Post

    Feed table sensor led

    Hi sir: Try to interchange the sensor amplifier, by those are working. However clean very well, the Edge connector of the PCB from sensor Amp....
    Post by: CHOCK, Apr 18, 2024 in forum: Komori Printing Presses
  9. CHOCK
    Post

    Polar 115EL cutting problems

    Dear Sir: is not + 42 is : -42Vdc, and then followed the -42 VDC, according with the Schematics;and see Where's the -42 VDC, is Missing!!, there...
    Post by: CHOCK, Apr 14, 2024 in forum: Cutters and Trimmers
  10. CHOCK
    Post

    Polar 115EL cutting problems

    Hi Sir: when you press the cut buttons, b 28a+ b 28b; the Relais D 21a+ D 21b, must pull in!! However test : Regulated power Supply: -42V, if is...
    Post by: CHOCK, Apr 13, 2024 in forum: Cutters and Trimmers
  11. CHOCK
    Post

    Error E01 pressure adjustment unit on Komori printer, please help

    Thanks You Sir. Great job.! Blessings.
    Post by: CHOCK, Apr 11, 2024 in forum: Komori Printing Presses
  12. CHOCK
    Post

    Error E01 pressure adjustment unit on Komori printer, please help

    What console model of PQC, do You have? Let me know. I Would like, that you send me, Pictures of Voltages?? Blessings
    Post by: CHOCK, Apr 10, 2024 in forum: Komori Printing Presses
  13. CHOCK
    Post

    Technotrans filter bag.

    Hi sir: What model do you have from Technotran?
    Post by: CHOCK, Apr 10, 2024 in forum: 4-Color Offset Presses +
  14. CHOCK
    Post

    Error E01 pressure adjustment unit on Komori printer, please help

    Hi , what PQC, do you have ?? Some time is the Thickness of paper, or the Regulated Power Supply out of Tolerance...!
    Post by: CHOCK, Apr 10, 2024 in forum: Komori Printing Presses
  15. CHOCK
    Post

    KBA Please Wait... screen

    OK sir. Blessings
    Post by: CHOCK, Apr 9, 2024 in forum: KBA Printing Presses