Recent Content by charlieapps123

  1. charlieapps123
    Post

    Xerox iGen 5-150 Versus Konica Minolta AccurioPress C14000

    Yes it is.
    Post by: charlieapps123, Jul 2, 2021 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  2. charlieapps123
    Thread

    Xerox iGen 5-150 Versus Konica Minolta AccurioPress C14000

    Anyone out there have any opinions about the iGen versus Konica Minolta AccurioPress C14000 I'd be grateful for your comments. We currently have...
    Thread by: charlieapps123, Jun 30, 2021, 2 replies, in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  3. charlieapps123
    Post

    Paper Jamming on Stripper Feet

    Turn the stock over.
    Post by: charlieapps123, Apr 29, 2018 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  4. charlieapps123
    Post

    fuser roll looks bad...

    We've had exactly the same problem here. Fuser maintenance done regularly so didn't need doing when the fault occurred. Tech had no idea so went...
    Post by: charlieapps123, Dec 19, 2017 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  5. charlieapps123
    Post

    Solid backed gloss adhesive paper SRA3

    Hi thanks for your reply. Yep SRA3 is 12 x 18 inches approx. Cutting the sheets down leaves a sticky edge which then damages the belt. A lot of...
    Post by: charlieapps123, Dec 5, 2017 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  6. charlieapps123
    Thread

    Solid backed gloss adhesive paper SRA3

    Hi. I'm actually running an iGen 5-150 so I hope this is the right place to ask this question. Does anyone run solid backed gloss adhesive paper...
    Thread by: charlieapps123, Nov 28, 2017, 3 replies, in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  7. charlieapps123
    Post

    Preventative Mainentance iGen 150, Xerox 1000

    Ok. The 4 fingers that lift the paper off the fuser are the stripper fingers and I only clean them when I change a fuser roll. I only clean the...
    Post by: charlieapps123, Aug 28, 2017 in forum: Xerox Digital Presses
  8. charlieapps123
    Post

    Preventative Mainentance iGen 150, Xerox 1000

    OK. This is what i was told during initial iGen 5 - 150 training. Don't do any maintenance unless the "maintenance turtle" ( warning scale) tells...
    Post by: charlieapps123, Aug 11, 2017 in forum: Xerox Digital Presses
  9. charlieapps123
    Post

    Xerox iGen5 + 5th color orange/clear + thick stock option

    You need to do CMT including TRC linearization when swapping to 5th colour. Takes more than 3 seconds I find.
    Post by: charlieapps123, Jul 18, 2017 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  10. charlieapps123
    Post

    Xerox iGen5 + 5th color orange/clear + thick stock option

    iGen 5 - 150 will handle a sheet 350gsm up to 500 microns as standard. Changing the print engine engine from full colour to full colour and 5th...
    Post by: charlieapps123, Jul 18, 2017 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  11. charlieapps123
    Post

    iGen 5 -150 with Fiery RIP Cycles down between sets with separator sheet (slip sheet)

    No I didn't
    Post by: charlieapps123, Aug 11, 2016 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  12. charlieapps123
    Post

    iGen 5 -150 with Fiery RIP Cycles down between sets with separator sheet (slip sheet)

    Can you offset XXL sheets
    Post by: charlieapps123, Aug 11, 2016 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  13. charlieapps123
    Post

    C16-350 + Failing System Check

    Don't be green - leave her on - you'll get far less error codes and no puddles.
    Post by: charlieapps123, Aug 10, 2016 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses