Trouble sm102 slt

Discussion in 'Heidelberg Printing Presses' started by Hendroloei, Dec 18, 2018.

  1. Hendroloei

    Hendroloei Member

    Joined:
    Dec 2018
    Messages:
    8
    Location:
    Indonesia
    My machine cannot running or rolling. Because the voltage is over 400v.
    After that. I call engineer work service my electronic.
    First init test1. Sltcon 5bff
    After service
    Svt flashing.
    IMG-20181218-WA0022.jpeg IMG-20181218-WA0002.jpeg
     
  2. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    "SVT Defective" according to code translation. Also, one mention of 120V circuit fail. Check GRM for proper incoming AC and outgoing DC voltages.
     
  3. Hendroloei

    Hendroloei Member

    Joined:
    Dec 2018
    Messages:
    8
    Location:
    Indonesia
    No trouble for incoming ac and dc voltages.
     
  4. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Hi
    What:
    1) is the Input voltage are you using in the machine 102 SM?
    2) What cp tronic use ? or Cpc?
     
  5. Hendroloei

    Hendroloei Member

    Joined:
    Dec 2018
    Messages:
    8
    Location:
    Indonesia
    1. My input 3phase 380v. After error n my machine cannot run. My input become 405v. And then i complaint for electricity. Now my input power stabilize become 380-390v.
    2. I using cp tronic. I dont know about what model, im not intelect about engine n software. IMG-20181217-WA0003.jpeg
     
  6. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Hi
    I can understand.
    Try to adjust the tap of primary winding in the main transformer of the machine
    2) measure the power supply electronic +5+24Vdc,etc see your schematic diagrams if there in tolerance.
    Not more higher than 0.7% or down,otherwise you must repair or replace the electronic board
    3) if the voltages fluctuation is very Heavy try to install Relay stabilizer from Heidelberg manufacturer, otherwise you must have many problem like
    this..
     
  7. Hendroloei

    Hendroloei Member

    Joined:
    Dec 2018
    Messages:
    8
    Location:
    Indonesia
    Thnks mr chock. The trouble not from power suply or transformer. I just try a srk board from my friend. And i tested, the trouble between svt or srk. Its very difficult. Because the price in here not cheap.
    Im from indonesia. N the technian from here, ex heidelberg. Technician heidelberg indonesia cant compre with europe or america.
    Maybe i need 3 until 4 days again. After i got news from my technician. I will post again
     
  8. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    o.k
    However , i must remember that you must measure the power supply +5Vdc example +24Vdc : example : if you measure 5.4 o 5.5Vdc must be replace and goes on, or less.
    Please let me know sir.
    The fluctuation can be damaged the power supply.
    Send me please a lecture-Pic : from +5Vdc
     
  9. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    So many complaints of “it’s too expensive”, “it’s not cheap here”...the control boards are ungodly expensive in the US also, it’s the cost of being in business.
     
  10. Hendroloei

    Hendroloei Member

    Joined:
    Dec 2018
    Messages:
    8
    Location:
    Indonesia
    Mr chock. I got it what trouble. Is come from gnt.
    And just my sbm will be repair. After sbm its done.

    To mr junker. Its cost expensive. Because my economic not good. I use Indonesian rupiah to convert euro, its expensive for me
    Thanks
     

    Attached Files:

  11. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    ok sir.
    I can understand.
    Let me know any question
     
  12. Hendroloei

    Hendroloei Member

    Joined:
    Dec 2018
    Messages:
    8
    Location:
    Indonesia
    3 days again we celebrate xmass. Thank you. May i know sor. Machine under 2000 and over 2000. What diferrent?
     

  13. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    some better performance
     
Loading...