The Wiki of Fault Codes!

Help with a XPE-08-3251 CCD Repeated Pixel Fault ?

 

Check your registration area. Clean glass, sensors and CCDs. Make sure you remove the glass and clean underneath and the reflective surface above. If that doesn't help, one of your CCDs in the registration area may be bad.

 

Xpe-06-3060 for igen4

@ ddigen4 XPE-06-3060 lists as Image Registration Setup Failure.

I've done the following:
-- cleaned the ETAC & MOB sensors
-- cleaned the shield over them
-- ran dc0610 iOi setup MOB Sensor Calibration (passed)
-- ran dc0610 iOi setup Automatic setup (passed)
-- ran dc0951 Xerographic Setup (passed)
-- lastly ran color maintenance ( passed)

Problem solved..

 

Wiki faults

Hi
Anyone have any experience with this one XPE-09-3753.
Press went down for no reason in the middle of a big variable data run.

 

That is a phantom error. I would reboot the server. Not listed in the EDOC. Maybe even the PSIP it that doesn't help.

 

This is a carrier dispense fault for Cyan. Most likely the magnet arm pin has broken

--
Mark

 

Spot on Mark!
Pin had snapped on solenoid actuating arm.
Requiring new parts fitting and press down for 4 hours.

 

My goof thought it was an iGen 3

 

1. XPE-09-8000
2. Print Engine Fault: Max Limit for System Deadcycle Exceeded
3. Place a service call and request a new iGen. Or click RESET under the "grin&bearit" tab.
4. Let me know which one works better for you.

pulled from earlier post....

Saw this error today...got a good laugh... ONLY because Igen started back up... Im thinking.. "I dont see a 'grin and bear it' button!!!!"

LOL!!!!

I hope it stays running.

 

Can somebody help with this
XPE-10-4121 Press Fault _Restart Press

I know there is another thread about this code 10-4121 for Fuser temperature. but this error is Press Fault

Please help

thank you

 

joinnow:

Hope this will correct your problem with External Roll #2 temp.

To Reset the fault, Enter [Marker, dC330 - Component Control, 10B Fuser Lamps]
folder. Then Exit the Fuser Lamp folder.

Good luck
Angel

 

Thanks alot lopeza

 

adding to thread for future reference:

XPE-09-3168. happens during dc0951.

I had just cleaned etacs and mob sensors. Think i smeared one? AND might have not got that ETACS cover back on evenly?

also pinscorotrons were aged. replaced

 

XOS-11-3054 - VGT 1 Motor Power Saturation

So I was getting this Friday on my 150, and called service and my tech told me he saw nothing about it other than maybe a dirty sensor. Cleaned them and was still getting it. So I took the stacker cart out and slid in to look around.

I noticed that there was a spring hanging down from one side of the slot where the paper enters the stacker. I tried just putting it back in place, but there was no tension.

Turned out the 2 springs had lost all of their tension and so we zip tied the springs really tight and put them back in and it's working great.

Hopefully this helps, should anyone ever have that same fault.

 

X2F-07-3147 and X2F-07-3148

Hi
Anyone have any experience with this X2F-07-3147 and X2F-07-3148
Thanks.

 

heres a solved error for reference.

got these RIGHT at end of day yesterday. frustrating...so went home to think about it....

xpe-03-4045 and xpe-04-4046 these were decurler errors. communication I guess... I found no way to clear it. In diagnostics, the decurler area was unresponsive.

the only solution was restart press, error gone

 

Igen 4 Xpe-09-3192 How to fix ??

 

hello there, welcome to the site. That ones not ringing too many bells for me...

Firstly, are there any other errors along with it? If you open diagnostics, what is the error called, that will help.

I'd pop open the belt clean the etacs.....then check for something not seated right maybe not sure. then try reboot if I didnt know what the error was called.

someone else here might have seen that one?

 

sorry for not answering sooner - i work graveyard shift and don't normally have time to get on web.

anyway xpe-09-3192 is:
tab blade motor fault
all i know is if reboot doesn't fix - call for service

 

XPE - 09 - 3089
Call for service....anything I can do to fix this?