Ryobi 3404 fault

Discussion in 'DI Presses' started by Annelies, Apr 4, 2020.

  1. Annelies

    Annelies Member

    Joined:
    Apr 2020
    Messages:
    6
    Location:
    Netherlands
    After an exposion problem our machine is jammed. Showing fault e031 with following text: the rotation preventing latch goes off during the imaging or goes on except during the imaging. Anybody with a suggestion or an explanation for resolving this problem?
     
  2. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Hi look for this sir:
    During the measurement, the scanner is not moved within 2 seconds
    after double clicking the start key.
    The communication cable is disconnected.
    The power cable is disconnected.
    The measurement bulb has burned out.
    Check and correct the situations above, then perform the measurement
    again.

    Blessing
     
  3. Annelies

    Annelies Member

    Joined:
    Apr 2020
    Messages:
    6
    Location:
    Netherlands
    Excuse me but what measurement are you talking? it's the press which is blocked. Or do I misunderstand you. Thanks for your reply
     

    Attached Files:

  4. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Test this sir:
    The communication cable is disconnected,or faulty

    The power cable is disconnected, or faulty test the power supply too.

    Blessing
     
  5. Annelies

    Annelies Member

    Joined:
    Apr 2020
    Messages:
    6
    Location:
    Netherlands
    I check it tomorrow.
     
  6. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Done

    Blessing
     
  7. Annelies

    Annelies Member

    Joined:
    Apr 2020
    Messages:
    6
    Location:
    Netherlands
    After doing this an restarting the machine, the fault is gone, but when any button is pressed, the fault comes back
     
  8. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    please Test:
    1) the cables communication +power for faulty,for continuity or Open

    2) clean very well the Edge connectors board, with special clean contact spray( almost all the 80 % of failure in electronic ) is coming for this
    situation.

    Let me know, Blessing
     
  9. Annelies

    Annelies Member

    Joined:
    Apr 2020
    Messages:
    6
    Location:
    Netherlands
    Where is that board located sir?
     
  10. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Sorry.
    Is all Electronic boards of the machine clean Very well!!!

    Blessing
     
  11. Chris RPC

    Chris RPC Member

    Joined:
    Sep 2015
    Messages:
    6
    Location:
    Central IL
    Did you get it figured out? Your machine might need clutches engaged/disengaged, possible need to crank the machine by hand to a certain spot and to get everything working together again. Best to call a service tech.
     
  12. marcelo6482

    marcelo6482 New Member

    Joined:
    Mar 2020
    Messages:
    2
    Location:
    Argentina
    Hello, you need to clutch the machine,

    PRINT / MANUAL PRINT / CLOCHE

    If it does not do it automatically you must do it manually:

    siscar 510 * / cloch service (code 5554- srv2- cluch on - off) / move the crank a little / remove cloche / turn until it falls / turn up to 510 *
    off on
     

  13. Emmanouil

    Emmanouil New Member

    Joined:
    Apr 2021
    Messages:
    1
    Location:
    Greece
    Hello I have the same problem...
    How can I do it manually
    Where I find siscar 510??
    Please can you help me??
     
Loading...