Replacing red plasma screen with LCD screen on Polar E, ED first series
- Thread starter eurogservice
- Start date
Alonex
Senior Member
Dear Eurogservice,
Again? Red, Orange,.. do you write a dissertation in daltonism?
It was explained you once - no one:
https://www.colorprintingforum.com/...f-orange-plasma-screen-with-lcd-screen.23293/
However, we could arrange and offer a kit for very hard-bitten and tedious students:
1. CCD Color(color-must) Video camera capturing pictures on the original Polar screen.
2. A personal computer with a frame graber card and corresponding application program. The computer may be excluded of the kit, if analogue camera and monitor are enough.
3. A VGA LCD Monitor.
4. Color palette instruction.
5. A mains cable with safety instruction.
As well, for local users we perform repairing of the existing Polar LCD screens, and replacing Polar CRT screens all over The World:
http://www.alonex.com/pdf/AX-PLR.pdf
http://www.alonex.com/pdf/F-AX-PLR.pdf
Regards,
Oleg T.
Again? Red, Orange,.. do you write a dissertation in daltonism?
It was explained you once - no one:
https://www.colorprintingforum.com/...f-orange-plasma-screen-with-lcd-screen.23293/
However, we could arrange and offer a kit for very hard-bitten and tedious students:
1. CCD Color(color-must) Video camera capturing pictures on the original Polar screen.
2. A personal computer with a frame graber card and corresponding application program. The computer may be excluded of the kit, if analogue camera and monitor are enough.
3. A VGA LCD Monitor.
4. Color palette instruction.
5. A mains cable with safety instruction.
As well, for local users we perform repairing of the existing Polar LCD screens, and replacing Polar CRT screens all over The World:
http://www.alonex.com/pdf/AX-PLR.pdf
http://www.alonex.com/pdf/F-AX-PLR.pdf
Regards,
Oleg T.
Advertisement:
eurogservice
Member
Oleg ... this comment is only for technicians in the field.
You don't know what you're commenting on!
Your merchandise is worthless...and so are your opinions !
Stop commenting!
Alonex
Senior Member
Dear Eurogservice,
Stop buzzing the forum with serial and stupid questions. My comment was exactly for you. Place it in a metal frame on your machine and ground it with proper cuprum wire. Read it each time you wish to place a new such post regarding a new color of your monochrome LCD display.
Regards,
Oleg T.
Stop buzzing the forum with serial and stupid questions. My comment was exactly for you. Place it in a metal frame on your machine and ground it with proper cuprum wire. Read it each time you wish to place a new such post regarding a new color of your monochrome LCD display.
Regards,
Oleg T.
eurogservice
Member
Oleg
You lack the most basic technical knowledge. Confuse color with technology.
It's not my fault you don't know about the existence of "monochrome plasma screens"!
There are few technicians who are able to replace a plasma monitor (technology) with an LCD monitor (technology) ... it is not for opinionated people!
You lack the most basic technical knowledge. Confuse color with technology.
It's not my fault you don't know about the existence of "monochrome plasma screens"!
There are few technicians who are able to replace a plasma monitor (technology) with an LCD monitor (technology) ... it is not for opinionated people!
Alonex
Senior Member
Dear Eurogservice,
Again, no one can replace "plasma", monochrome nor color display in the existing Polar control with another LCD display with non-standard nor standard interface. Only a display with the same digital video interface can be used as replacement.
Could you please provide the type of "plasma" display in your Polar E, ED for verification and learning?
Regards,
Oleg T.
Again, no one can replace "plasma", monochrome nor color display in the existing Polar control with another LCD display with non-standard nor standard interface. Only a display with the same digital video interface can be used as replacement.
Could you please provide the type of "plasma" display in your Polar E, ED for verification and learning?
Regards,
Oleg T.
eurogservice
Member
Oleg
Polar itself built the first E ED models with plasma monitors!
They were later replaced by more reliable and economical LCD models. It can't be, it's just your limit!
I can provide documentation...only for COMPETENT technicians. IT'S NOT YOUR CASE!
Polar itself built the first E ED models with plasma monitors!
They were later replaced by more reliable and economical LCD models. It can't be, it's just your limit!
I can provide documentation...only for COMPETENT technicians. IT'S NOT YOUR CASE!
Advertisement:
Alonex
Senior Member
Dear Eurogservice,
The first and the last Polar E/ED were built with usual back-lit LCD displays, until you would prove existence of "plasma" in Polar E/ED onece. The "few" technicians who "are able" to replace a "plasma" monitor with another LCD display - are your imaginations, when you culculated yourself multiple times, as a "few", and each time in a different color.
Regards,
Oleg T.
The first and the last Polar E/ED were built with usual back-lit LCD displays, until you would prove existence of "plasma" in Polar E/ED onece. The "few" technicians who "are able" to replace a "plasma" monitor with another LCD display - are your imaginations, when you culculated yourself multiple times, as a "few", and each time in a different color.
Regards,
Oleg T.
Last edited:
Alonex
Senior Member
Dear Eurogservice,
1. Yes, after more deep investigation of the subject, with a great surprise, I have to state that Polar indeed tried to push plasma monochrome displays into E & ED machines, at least hypothetically, since we have never seen such execution of Polar controls.
2. Yes, we could replace a plasma display with a LCD of a proper dimention and with a proper digital video interface. This is a real task, however, it could not be an one-by-one "replacement" on the fly, or via DHL. It may reuire some modifications of the service voltages/intefaces/cables, and may be reconfiguring of CP card as well. Input data required: The plasma display type/dimention, HW and SW revisions of the following cards: CP, KC, ADA. Acessilabilty of the target Polar machine/control, and a formal inquiry via encrepted chanel of our embassy are required.
3. The more interesting task of standard monitors' adaptation to the Polar machines are still under investigation and development. Informative and financial contributions would be very useful.
4. My old comment (from Feb 13, 2023) in the grounded frame may be replaced with another one as below:
"Do not begin a new post, while your previous one was not formed properly, and has been left at all. Form any post/problem as full and accurate as possible, share more and more information when you expect to get adequate and full response" (The frame grounding is not mandatory now, but the gold frame is).
Regards,
Oleg T.
1. Yes, after more deep investigation of the subject, with a great surprise, I have to state that Polar indeed tried to push plasma monochrome displays into E & ED machines, at least hypothetically, since we have never seen such execution of Polar controls.
2. Yes, we could replace a plasma display with a LCD of a proper dimention and with a proper digital video interface. This is a real task, however, it could not be an one-by-one "replacement" on the fly, or via DHL. It may reuire some modifications of the service voltages/intefaces/cables, and may be reconfiguring of CP card as well. Input data required: The plasma display type/dimention, HW and SW revisions of the following cards: CP, KC, ADA. Acessilabilty of the target Polar machine/control, and a formal inquiry via encrepted chanel of our embassy are required.
3. The more interesting task of standard monitors' adaptation to the Polar machines are still under investigation and development. Informative and financial contributions would be very useful.
4. My old comment (from Feb 13, 2023) in the grounded frame may be replaced with another one as below:
"Do not begin a new post, while your previous one was not formed properly, and has been left at all. Form any post/problem as full and accurate as possible, share more and more information when you expect to get adequate and full response" (The frame grounding is not mandatory now, but the gold frame is).
Regards,
Oleg T.
Last edited:
Forum posts represent the experience, opinion, and view of individual users. The Color Printing Forum does not necessarily endorse nor share the view of each individual post.
When making any potentially dangerous or financial decision, always employ and consult appropriate professionals. Your circumstances or experience may be different.
