Polar EM115 Error 94

Discussion in 'Cutters and Trimmers' started by Berghy, Dec 4, 2017 at 8:38 PM.

  1. Berghy

    Berghy Member

    Joined:
    Monday
    Messages:
    6
    Location:
    New Zealand
    We have a Polar Mohr Guillotine EM115 which is giving us error 94. I have a list of the error codes and this is not on it. Does anyone know what error code 94 means? Note it is error 94 not 92.
     
  2. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    570
    Location:
    Managua
    Hi sir
    Good day hope you are well
    Your mean: Knife running time upper dead.-pt lower dead pt.and lower deat pt.
    /upper deat pt. exceed . Please check the hydraulic circuit P2 valve Y330 see the schematic
    diagrams+and Hydraulic schematic.TEST card SH +HK
    Let me know
    Blessing
    superchock@yandex.com
    cell+whatsApp: +50588611441
     
  3. Berghy

    Berghy Member

    Joined:
    Monday
    Messages:
    6
    Location:
    New Zealand
    Thanks Chock
    I have spare parts catalogue with the exploded views of the components, but this doesn't show hydraulic circuit P2 or valve Y330.
    Can you let me know where to find them in the machine ??
     
  4. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    570
    Location:
    Managua
    Hi, the spare parts catalogue, does NOT show the nmber of valve Y330, only the schematic diagrams
    I suppose the you have Schematic D , is coming with any machine.
    Let me know or send me email
    Blessing.
    superchock@yandex.com
    cell+whatsApp: +50588611441
     
  5. Berghy

    Berghy Member

    Joined:
    Monday
    Messages:
    6
    Location:
    New Zealand
    Hi Chock
    I don't have the schematics for the hydraulic systems.
    Can you advise where to find Y330, or perhaps send through Schematic D.
    Thanks
     
  6. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    570
    Location:
    Managua
    look in the board SH Connector Oh 203.6+oh203.4 =+42Vdc
    Y330 LED v2 must turn On, when activaded
    Thanks. I can NOT send you any Diagram through the Forum
    Blessing.
    superchock@yandex.com
    cell+whatsApp: +50588611441
     
  7. Berghy

    Berghy Member

    Joined:
    Monday
    Messages:
    6
    Location:
    New Zealand
    Hi Chock
    I have been manually winding the blade to the top and restarting the guillotine. It then seems to run ok for 1-2 hours then errors with code 94. Just now it has stopped with error 85.
    We don't have an SH board. The only boards I can see are PS5, SPE, HR, AR, EI, WSP, PS24, TAM, IHR, IAR, KK, HK
    Any advice appreciated!
    Thanks
     
  8. Berghy

    Berghy Member

    Joined:
    Monday
    Messages:
    6
    Location:
    New Zealand
    Just found another issue. The guillotine operates without press the foot pedal. You only have to push the 2 hand buttons, then the bar comes down very quickly, then the knife cut.
    We have stopped using the machine and locked it.
     
  9. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    570
    Location:
    Managua
    Good day sir.
    Sorry you do not have Sh board, this special card for special Hydraulic y330
    However the error 85, this special situation since you must carrier many adjustments
    and see the LED diodes in the differents boards: 1) All LEDS in HK +IAR You need special tech documentation
    2) ADJUST Limit swtich b22a+b22b
    3) adjust light barriers
    4) depend of what you did, so you must replace or HK+KK+IAR+AR
    Please send me email
    Blessing.
    superchock@yandex.com
    cell+whatsApp: +50588611441
     
  10. Berghy

    Berghy Member

    Joined:
    Monday
    Messages:
    6
    Location:
    New Zealand
    Thanks Chock
    Time to admit defeat and call in the technicians.
    Thanks heaps for all your help.
     

  11. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    570
    Location:
    Managua
    Sorry but, some time
    some problem are more complicated, and do not have
    solution by Chat.
    However any question , you can send me email
    o try contact me.
    Blessing.
    superchock@yandex.com
    cell+whatsApp: +50588611441
     
Loading...

Share This Page