Help! Heidelberg GTOZP-52

Discussion in 'Heidelberg Printing Presses' started by Yoshi, Apr 6, 2021.

  1. Yoshi

    Yoshi Member

    Joined:
    Feb 2019
    Messages:
    7
    Location:
    Washington
    Hi Guys,

    I've been trying to locate a "cog or teethed" belt for my GTO52. But, I've had no luck. I've attached a diagram with some measurements of it. I do not have a manual or parts manual unfortunately, so I've just been scouring the net for a belt with similar measurements. Insofar, I've purchased this belt on ebay, 1828V368 00.270.0076, but that belt was not it.

    The machine won't run without this belt. So, I know that it is some sort of timing or motor belt.

    Thank you for your time!
     

    Attached Files:

  2. mantman

    mantman Senior Member

    Joined:
    Nov 2015
    Messages:
    198
    Location:
    Greece
    Did you check your parts book? There are all parts of machines with specific codes
     
    Yoshi likes this.
  3. SAICPRINT

    SAICPRINT Member

    Joined:
    Feb 2014
    Messages:
    35
    Location:
    Chicago
    I think yours might be 270.0068 for zp press
     
    Yoshi likes this.
  4. Yoshi

    Yoshi Member

    Joined:
    Feb 2019
    Messages:
    7
    Location:
    Washington
    I don't have a parts book, unfortunately. I am looking for one, though, so I'd greatly appreciate any advice on where to get one.
     
  5. Yoshi

    Yoshi Member

    Joined:
    Feb 2019
    Messages:
    7
    Location:
    Washington
    Hey! Thank you. I'll contact a supplier and see if that code brings up the belt!
     
  6. mrheidelberg

    mrheidelberg Senior Member

    Joined:
    Jan 2008
    Messages:
    708
    Location:
    United Kingdom
    What is the belt off ? (great diagram by the way :) )
     
    Yoshi likes this.
  7. mrheidelberg

    mrheidelberg Senior Member

    Joined:
    Jan 2008
    Messages:
    708
    Location:
    United Kingdom
    Yoshi likes this.
  8. Yoshi

    Yoshi Member

    Joined:
    Feb 2019
    Messages:
    7
    Location:
    Washington
    Thanks! I was hoping somebody would enjoy it! I am working on getting a picture of where it was taken off of. I bought this item: https://www.ebay.com/itm/Belt-For-H...-270-0076-Offset-Printing-Parts-/263047891817 and the circumference was too short at 934mm. The teeth were also smaller and thus couldn't even fit the gears on the GTO52.

    I think that might be the belt I am looking for! I'm trying to find a US seller for it. I think shipping and the time frame for getting one from Europe might be exorbitantly prohibitive.
     
  9. Yoshi

    Yoshi Member

    Joined:
    Feb 2019
    Messages:
    7
    Location:
    Washington
    I think they have a branch in the US, so I hope they can assist me with finding that belt. Thank you for your help, hopeful that it will be a good fit when it arrives. My worry is that the belt itself looks wider (based on specs from another website) by about 5mm. Would you happen to know where one can get a parts manual for my machine?
     
    mrheidelberg likes this.

  10. mrheidelberg

    mrheidelberg Senior Member

    Joined:
    Jan 2008
    Messages:
    708
    Location:
    United Kingdom
    The parts book is copyrighted so unless you can get 1 off Ebay or you could try a 2nd had machine dealer, you may have to go direct to Heidelberg.
     
Loading...