Search Results

Search Again
Page 1 of 2
  1. simon yeung
    Post

    POLAR 115 EM and 115EMC position not achieved

    Hi mbosko, Please don’t get happy too early because the problem still there. This problem cause by the software inside board "AR" , so you need...
    Post by: simon yeung, Aug 19, 2015 in forum: Cutters and Trimmers
  2. simon yeung
    Post

    POLAR 115 EM and 115EMC position not achieved

    Hi mbosko, It seems the software cause this problem, short slow down travel. Try re-scanning reference point (While the backgauge moving turn off...
    Post by: simon yeung, Aug 19, 2015 in forum: Cutters and Trimmers
  3. simon yeung
    Post

    Polar 76 EM - error 92 -

    try replace the capacitor c16 (6.8uf/40v). http://www.welvin.com Simon yeung
    Post by: simon yeung, May 5, 2015 in forum: Cutters and Trimmers
  4. simon yeung
    Post

    Polar 115 EMC brain failure!?

    Hi Nadg63, Did you check the spindle nuts and the motor brake?
    Post by: simon yeung, Dec 7, 2014 in forum: Cutters and Trimmers
  5. simon yeung
    Post

    Error 79 on Polar Mohr 92-E.

    Hi wunmi-50 Please take a look at this diagram [img] for motor brake gap. Listen, I can't convert you to a polar guy for such few words; if you...
    Post by: simon yeung, Nov 23, 2014 in forum: Cutters and Trimmers
  6. simon yeung
    Post

    Error 79 on Polar Mohr 92-E.

    Hi wunmi-50 Error No. : 79 Error message : position not achieved cause: This error message is indicated after a positioning process, if it is...
    Post by: simon yeung, Nov 22, 2014 in forum: Cutters and Trimmers
  7. simon yeung
    Post

    72 CE Down any ideas??

    check the card no. 2 for +6v and -6v also card no. 3 +24v.
    Post by: simon yeung, Oct 23, 2014 in forum: Cutters and Trimmers
  8. simon yeung
    Post

    MHS M226598 in TAM and PI

    Hi coloured paper Our LMS mod. set will give the same accuracy as the original POLARTECH LMS since it designed for perfectly replacement of Polar...
    Post by: simon yeung, Aug 18, 2014 in forum: Cutters and Trimmers
  9. simon yeung
    Post

    MHS M226598 in TAM and PI

    Hi NimehSilva, Please consider our LMS mod. set if you are looking for the linear measuring system.For details please visit our homepage.It...
    Post by: simon yeung, Aug 18, 2014 in forum: Cutters and Trimmers
  10. simon yeung
    Post

    Polar 92 CE Troubleshooting

    Hi zehspoon, I think you should check the n/c n/o contacts of saftey bolt switch(b SB)which located at the tail of the safety bolt and also the...
    Post by: simon yeung, May 8, 2014 in forum: Cutters and Trimmers
  11. simon yeung
    Post

    How to Fix Error 82 on Polar SDP 115

    Hi egyeng, Error detection signals:- number -82- Meaning:- During activating of locking valve - Y315 - the control transistor on card IAR does...
    Post by: simon yeung, Feb 5, 2014 in forum: Cutters and Trimmers
  12. simon yeung
    Post

    Polar 78 ES 1998 year model

    no such error code!!!
    Post by: simon yeung, Nov 21, 2013 in forum: Cutters and Trimmers
  13. simon yeung
    Post

    Polar Mohr 76em - Error 68

    Hi alleno Error --68-- means (In program no."0" the measurement for a special size false clamp has been stored, either being smaller than 1.8 cm...
    Post by: simon yeung, Sep 21, 2013 in forum: Cutters and Trimmers
  14. simon yeung
    Post

    Polar ed 92 display fault

    Hi vastanali please visit here http://presscity.com/en/Spare-parts/Polar-LCD-monitor-for-E-ED-cutting-machine/1834
    Post by: simon yeung, Sep 16, 2013 in forum: Cutters and Trimmers
  15. simon yeung
    Post

    error 82 on Polar 76EM

    Dear qure, error -82- cause by (During activating of locking valve -Y315 - the control transistor on card IAR does not function.) Check...
    Post by: simon yeung, Jun 15, 2013 in forum: Cutters and Trimmers
  16. simon yeung
    Post

    Polar EMC 92 memory saving problem - Please help

    You could try replace the battery inside the memory bank (N-WS) and try refresh it by erasing all the programs(1-98),hope it helps. please visit...
    Post by: simon yeung, May 27, 2013 in forum: Cutters and Trimmers
  17. simon yeung
    Post

    The Procedure to calibrate the TAM card on Polar SDP 115

    Hi egyeng and DigPrint, What error code number you are looking for?DigPrint.I can post here,but I can't post all of them. please read this:-...
    Post by: simon yeung, Sep 11, 2012 in forum: Cutters and Trimmers
  18. simon yeung
    Post

    Polar Mohr 115

    Hi Dan, E/ED machine was the generation(1995-2005) before X/XT(2005 till now) both of them equiped with a LCD monitor but the EL(eltromat memory)...
    Post by: simon yeung, Aug 25, 2012 in forum: Cutters and Trimmers
  19. simon yeung
    Post

    Electrical Diagram for Trimmer Polar 72CS

    Hi Genu_Sut Please visit my site for any Polar spare parts or enquiries http://www.welvin.com or http://welvin.no-ip.org mail...
    Post by: simon yeung, Aug 21, 2012 in forum: Cutters and Trimmers
  20. simon yeung
    Post

    Frequency Conv. Signal Error 811

    http://img442.imageshack.us/img442/9269/sap78xt.jpg
    Post by: simon yeung, Aug 21, 2012 in forum: Cutters and Trimmers
Showing results 1 to 20 of 23 Next >
Search Again
Page 1 of 2