Search Results

Search Again
Page 1 of 2
  1. cisco605
    Post

    10-3307

    could be worn blue deculer rollers or are dirty and need cleaning. or sensor it failing could be loose in housing where it clips into .
    Post by: cisco605, Jun 19, 2019 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  2. cisco605
    Post

    Fuser not detacking

    Poor quality stock? trying using another 50# offset . Certain 50# will not run in igen constant jams, dog ears no matter how many jumpers you use...
    Post by: cisco605, Jun 18, 2019 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  3. cisco605
    Post

    Side 2 Image Quality Issue

    Replace the center etac. Classic running along and all of a sudden no mag cycle down restart mag comes back. Also if you have not redone mag...
    Post by: cisco605, Mar 12, 2019 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  4. cisco605
    Post

    Side 2 Image Quality Issue

    Hi Adam verify you have correct gsm in for your stock. Then under the stock your running in subsytem attributes adjust your transfer voltage up...
    Post by: cisco605, Mar 7, 2019 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  5. cisco605
    Post

    Fuser web repair kits

    604K67250
    Post by: cisco605, Jan 7, 2019 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  6. cisco605
    Post

    09-3163

    check the connection on the inboard black etac. make sure its clean. if that does not work replace it and you will be good to go. As far as the...
    Post by: cisco605, Sep 14, 2018 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  7. cisco605
    Post

    Magenta Slowly Washing Out

    you could try to increase your toner concentration on magenta. may need to redo developer in magenta. like stitch said which 9 times out of 10 the...
    Post by: cisco605, Jan 31, 2018 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  8. cisco605
    Post

    Fuser problem?

    there is a NVM to speed up or slow down the prefuser belts under psp but I do not recall the number. sheet will have a slight buckle as it enters...
    Post by: cisco605, Sep 14, 2017 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  9. cisco605
    Post

    Replace Waste Dry Ink Filter

    igens love uncle bens white
    Post by: cisco605, Nov 5, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  10. cisco605
    Post

    Replace Waste Dry Ink Filter

    it sounds like igen making popcorn :)
    Post by: cisco605, Nov 3, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  11. cisco605
    Post

    Replace Waste Dry Ink Filter

    I have a thought but use at your own risk disconnect the black hose that runs from the cleaner unit to the cyclone blower drop in a handful of...
    Post by: cisco605, Nov 3, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  12. cisco605
    Post

    help. 10-3112 then 10-5009.

    Also the thermistor on x rollers will cause problems from build up. I will wipe them off with my scotch bright pad .
    Post by: cisco605, Nov 3, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  13. cisco605
    Post

    Page corners folding

    if the decurler rollers feel sticky the sheets will stick to the rollers.after cleaning rollers I use a little spray powder to reduce tack.May...
    Post by: cisco605, Jul 29, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  14. cisco605
    Post

    Going through fuser rolls too fast

    running fuser fluid 2 will also make your fuser roller last longer has more viscosity.
    Post by: cisco605, Jun 1, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  15. cisco605
    Post

    Going through fuser rolls too fast

    yes that is a tough one to see visually they do look fine. but the roller has a some what coarse finish on it which will wear down after time. I...
    Post by: cisco605, Jun 1, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  16. cisco605
    Post

    Going through fuser rolls too fast

    have you replaced the metering roller in the fuser tray when they go bad they will cause problems? also the wick under the metering roller and the...
    Post by: cisco605, May 29, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  17. cisco605
    Post

    Xpe-09-1100 doa

    Also wipe the black patch generator.its the sensor just above etacs.toner on this will cause the xpe-09-1100.
    Post by: cisco605, May 11, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  18. cisco605
    Post

    7B Will Not Clear After Jam

    jam possible dirty sensor clean,the nut holding it in place came loose and moved or sensor is just bad ?
    Post by: cisco605, Jan 30, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  19. cisco605
    Post

    XPE-xpe-10-1105

    xpe10-1105 wipe sensor by pressure roller and the area above sensor some times it will get fuser oil on it causing the fault ,verify that its...
    Post by: cisco605, Jan 16, 2015 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  20. cisco605
    Post

    HAHAHA you won't believe this one!

    yeah the bigger problem when untrained operator dumps fuser fluid in the carrier opening. very messy :)
    Post by: cisco605, Nov 12, 2014 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2