Search Results

Search Again
Page 1 of 2
  1. iGenTech
    Post

    Magenta spitting

    You can vacuum the developer out of the trickle tube from the top. Then feed a 10 gage wire down the tube to brake up any thing that is stuck. The...
    Post by: iGenTech, Nov 19, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  2. iGenTech
    Post

    Deletion/Image issue (PICS)

    RMigen, The last time I seen this problem it was a bad new fuser roll. The circumference of the roll was to small which was slowing down the...
    Post by: iGenTech, Nov 15, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  3. iGenTech
    Post

    Velocity Measurement Instrument Project

    Sunshine, Paper motion on most printers is based on fixed RPMs 50/60hz of the paper path motors. On most there is a master clock we call...
    Post by: iGenTech, Nov 11, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  4. iGenTech
    Post

    PR belt stripper finger marks

    Stiv, :-) it's never the stock.... FYI you can remove the belt stripper finger assy. It's one of those things I wish I had came up with. No...
    Post by: iGenTech, Oct 21, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  5. iGenTech
    Post

    PR belt stripper finger marks

    Stiv, I would be shocked if the scratches were from the p/r stripper fingers. I have seen the bottom plastic clip brake that latches it close but...
    Post by: iGenTech, Oct 13, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  6. iGenTech
    Post

    Thick Card stock in IGEN3

    Peels, Just make a shim. Say 5 inches wide and 1 1/2 inches thick, place it on the stacker cart about 4 inches from the right side. Also make...
    Post by: iGenTech, Oct 13, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  7. iGenTech
    Post

    Third party service for Igen3 110

    The down fall of Xerox. Diagnostics and over priced Parts and Supplies... CRocket, Don't hold your breath looking for third party igen...
    Post by: iGenTech, Jul 30, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  8. iGenTech
    Post

    Equipment Prices

    drlew, Igen3 start at $5,000 and go up. I just see 2 sell on eBay 2 feeders 2 stackers both with the finest front end the freeflow x86 and both...
    Post by: iGenTech, Jul 27, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  9. iGenTech
    Post

    Equipment Prices

    drlew, I know of 10+ igen3's. Email the specs you are looking for. Ie.type of frontend Creo, fiery, Free Flow, number of stackers, feeders or...
    Post by: iGenTech, Jul 24, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  10. iGenTech
    Post

    The Wiki of Fault Codes!

    XPE-10-3346 and XPE-10-3341 XPE-10-3346 and XPE-10-3341 Decurler Entrance/Exit missing +36vdc I havent checked to see where the +36vdc goes...
    Post by: iGenTech, Jul 14, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  11. iGenTech
    Post

    The Wiki of Fault Codes!

    Xpe-09-3066 RMiGen, XPE-09-3066 Is Transfer/Detack PS Overtemperature or Wire Current Fault Transfer/Detack Wire wire current is out of range...
    Post by: iGenTech, Jul 14, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  12. iGenTech
    Post

    Power requirement for Igen3

    Email me and I'll send you the install specs. Igentech@yahoo.com
    Post by: iGenTech, Jul 10, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  13. iGenTech
    Post

    Xpe-09-3167

    Meesh48 , I know I already answered this in wiki but reposting sense it was moved here. XPE-09-3167, indicates that during dC0951, the Center...
    Post by: iGenTech, Jul 8, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  14. iGenTech
    Post

    Rip card needed...

    Hi, Thy are used in the Xerox DC 242/252, 260, iGen3, other Rip's. Thanks
    Post by: iGenTech, Jul 8, 2011 in forum: Other RIPs
  15. iGenTech
    Post

    dC0610 Image Registration Setups

    Well I fourth that papapascucci with the add detail..... dC0610 (IOP) Image On Paper: Registration Setup is used to adjust the image...
    Post by: iGenTech, Jul 2, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  16. iGenTech
    Post

    The Wiki of Fault Codes!

    Yes, XPE-09-3167, indicates that during dC0951, the Center ETAC high target could not be determined. Check the following DC131 NVM value:...
    Post by: iGenTech, Jul 1, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  17. iGenTech
    Post

    Decurler really tacky..

    Hummmm the Good'O magic fairy dust man I love that stuff... It sounds more like a fusing issue. This also happens you don't have the stock...
    Post by: iGenTech, Jul 1, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  18. iGenTech
    Post

    The Wiki of Fault Codes!

    XPE-09-1100, indicates that Cycle-Up Convergence failed to complete in the time allotted. I don't like this code because it don't tell you what...
    Post by: iGenTech, Jul 1, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  19. iGenTech
    Post

    Igen3 digital press issues (Print Engine Fault code XPE-09-3503)

    Fault code XPE-09-3503 Fault code XPE-09-3503 Indicates that the Patch Generator LED intensity was unable to converge within the allowable...
    Post by: iGenTech, Jul 1, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
  20. iGenTech
    Post

    The Wiki of Fault Codes!

    XPE-09-3503 Patch Generator LED intensity Convergence Fault I would start by cleaning the Patch Generator. Its located in the middle just above...
    Post by: iGenTech, Jun 30, 2011 in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
Showing results 1 to 20 of 40 Next >
Search Again
Page 1 of 2