Search results

new DUO board in the DFE. so far so good tried the boards in back, even swapping fiberoptic cables to avoid that, guess its a 4500 dollar board lol

solved. Interesting one... board on the back of the developer station had the bottom connector come loose.....

***SOLVED see second post. Pinscorotron grid to PR slope out of range. accompanied "log only" faults: 09-4414 VMC at minimum 09-4464 developer VMAG at maximum swapped pinscorotrons -no change.... cleaned etacs, cleaning brush...still wont run and wont pass 951. its a new one on me.

hey @Milo Wilson I was out on vaca, this little nugget of an error came back... auto repair boot the dfe and it works...until you stop and start again. Runs prints fine from the PSP Xerox onsite again. DFE appears fine. So theyre swapping one of the boards. Ill update with solution.

no experience. but i do wonder the same. It cant be good. but no worse than other industry. and I wonder this about paper dust and other things involved with print... we all gotta go sometime. :(

so it does this ONLY on this offset stock. Stock which Iv'e used for years. and have confirmed wasn't changed. Runs copier paper ALL day. crazy annoying. theory: Bad fuser, heat/humidity, and porous light paper combined to cause issue. Hoping new fuser solves it.

You're a true gentleman, Milo. ;) But no need to call and cry on your shoulder today lol. Its friday. And besides, I have handed the ball off to the big red x. Other problems as well.....

FYI its back.... no accompanying errors. Once yesterday... shutdown this morning and ran. Just came back.... Ill check all the DFE stuff again...

thats just it, everything was fine. no communication errors... passed all print quality calibrations... Finally Got through it after a laundry list of errors.... eventually a new belt... cleaned the cleaning brushes.. Auto-repair boot of the DFE, full reseat of everything. everywhere lol...

well...its doing this again. outboard lead edge curled up, then down. "dog-eared" see photo paper is fine as it hits fuser, dog ears as it leaves the roller. everything i know to do is done. lol except for yet another fuser/pressure roll. its legit making me insane

also has"too many registration marks" at the MOB sensors 6-3015 6-3016 reboot, and cycle the DFE it ran for awhile... now im dead. :/

Ive had this before... but never on normal paper.. usually only REALLY light gloss. Paper coming through the transfer 'bubbles' or 'bows up' in the middle at the trail edge as its exiting, not allowing transfer in a 0.5" x 2" spot ...I do not remember what we did when it happened before....lol...

another new fuser, along with some of the changes I chronicled above, and its fine. just bad luck with fusers I guess...

got it running briefly cleaned the skive on back of fuser... (im sure theres a name...) the little jets. everything. adjusted it in a little, then changed some fuser airknife settings then it ran fine, but then jammed after 300 sheets. :( feel like I eliminated oiling by filling the metering...

Now its back. complete folds inboard and outboard edge...very bizarre... fuser appears oiled... dont think its that... too hot? all of a sudden my paper changed? fuser roller went bad? ugh lol

entrance decurler home position fault. comes and goes.... coming more than going.... here's what iv'e been doing.... 1-clean sensor 2-reseat connectors for sensors(multiple) 3-hand advance decurler cam shaft(not sure actual term) 4-reseat connector for decurler motor 5-reboot. if im IN...

Ive used this 50 for YEARS. its my #1 stock :) any amount of toner. I think you're onto something with the checking fuser ram etc.... I wiped the fuser with oil soaked rag and it started running briefly... maybe its getting under oiled? EDIT: reboot for 9-1100. now its running no...

still at this.... its sticking trying to roll up, but only on this one thin paper... that have to use constantly. 50# offset. 14x18 runs everything else fine. found my web had snapped... fixed that thought for sure that was it... nope. at a loss. it isnt that. Im well aware of that high...

fuser, pickers and pressure roller and its running.

software reload, followed by a connector loose on reg board.... few days down off and on. came back after the latter, absolutely will not run my daily 50 offset paper. Sticks and rolls up OB corner.. "late to fuser exit" runs card and postcard stock fantastically... It's quite seriously making...