Polar 115E - Knife Change

Discussion in 'Cutters and Trimmers' started by KhorWK, May 16, 2022.

  1. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    Can anyone help me to solve this issue? Its appear this problem everytime I on the machine, then it will stuck here. Press "1", go in selection of "Hard Material / Normal Material / Soft Material", but nothing can do. Can please advice how to check / resolve this issue?
     

    Attached Files:

  2. Mathew

    Mathew Senior Member

    Joined:
    Apr 2010
    Messages:
    530
    Location:
    Kolding-Denmark
    Hi,
    Try to replace battery on CP card. It seems you are missing some data each time the machine is switched OFF.
    Maybe you need to perform knife change program after the battery is replaced.
     
  3. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    I have checked the battery is no issue.
     
  4. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Hi sir;

    Go to Reset the electronic board CPU the small button black Printed Reset S1, and see what happens.

    2) The battery must be 3.6Vdc, if has 3.5Vdc or less, you must replace it; you have only 10 minutes to do it.
     
  5. ashok kumar

    ashok kumar Senior Member

    Joined:
    Nov 2017
    Messages:
    224
    Location:
    india
    Hi
    It means machine is not come in operation al mode.
    There is one sensors(for flap open) .
    When you change the knife then you move one flap up.
    For the same there is one sensor pls check that sensor when flap is closed then output of the sensor is 24v .
     

    Attached Files:

  6. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Please proceed with my steps

    Blessings

    @ing_dr
     
  7. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    The battery is 3.6vdc exactly, but still not workable.
     
  8. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    Thank you, will check it later.
     
  9. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Go to Reset the electronic board CPU the small button black Printed Reset S1, and see what happens.

    Did you do it ?



     
  10. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    Yes, this has been done many times but still the same problem.
     
  11. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Now, please measure the Regulated power supply, if there are intolerance: +5 +24+12, etc

    Very important, and if they ok, Please clean of edge connectors, of electronic boards, much of 70% of electronic failure, is to due this.

    Blessings
     
  12. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    Checked, no issue on power supply. But still the same problem...
     
  13. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Can You send me the Pics of each Regulated power supply please

    Blessings

    @ing_dr
     
  14. ashok kumar

    ashok kumar Senior Member

    Joined:
    Nov 2017
    Messages:
    224
    Location:
    india
    Had you check sensnor output or not
    At the back plane
     
  15. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Can You send me the Pics of each Regulated power supply please



     

  16. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Waiting Sir.

    Blessings
     
Loading...