Sm102-4

Discussion in '4-Color Offset Presses +' started by Beguin, Mar 18, 2021.

  1. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    hello dear elder, I have a problem with my sm102-4, when I press the command the compressor which makes the suction and the blower does not start to what this can be due when I make the direct command the compressor of and there are four KLM cards their LEDs go out thank god bless us.
     
  2. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Hi sir;

    Please reset the Thermic Switch; 15Q9+15Q22+15Q18+15Q28

    and tight very well, every wires of the respective Switches.

    Look, if there are dirty, clean with Special contacts cleaner, Turn OFF the machines.
     
  3. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    thank you dear elder Chock, I did it as you recommended to me but seems God bless us.
     

    Attached Files:

  4. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    what cptronic do you have?
     
  5. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    hello elder chock, it's
    Cptronic 2000
     
  6. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Hi look :

    1)for Circuit breaker Q 204+Q204G, Reset both circuit breaker for compressor.

    and tight very well the wires +clean for corrosion, input and output of circuit breaker.

    2) look if the Amperaje of circuit breaker is lower, increase the adjustment amperaje with small screwdriver,

    3)Finally the motor +compressor: Need complete Maintenance go to machine Shop and clean+lube+exchange ball bearing....etc , is a Powerful reason for to Trigger the Circuit breaker.

    Good luck

     
  7. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    always solution to my problem after following everything I was recommended. Please help please thank God bless us
     
  8. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Finally the motor +compressor: Need complete Maintenance go to machine Shop and clean+lube+exchange ball bearing....etc , is a Powerful reason for to Trigger the Circuit breaker.

    If you do that the Trigger circuit breaker will NOT do it. The winding motor can be Reheating(NOT burning) need make carefully repair in specialized machine shopt for electrical Motor. Please

    Did you do that sir?
     
  9. turbotom1052

    turbotom1052 Senior Member

    Joined:
    Oct 2008
    Messages:
    1,044
    Location:
    Vermont
    Not remembering if it affects all model years of Speedmasters but if your delivery pile is all the way down, or if the limit switch has failed, you will not be able to turn on your compressor
     
  10. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    problem solved thanks everyone.
     
  11. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    ok, sir Good job

     
  12. turbotom1052

    turbotom1052 Senior Member

    Joined:
    Oct 2008
    Messages:
    1,044
    Location:
    Vermont
    It would be in proper form to allow the forum membership to learn of your resolve.
     
    CSF likes this.
  13. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    it is thanks to your help that I arrived, thank you back to you. he had a connection of the Q202 which was not tight and that is from the factory. that was the problem. God bless us
     
  14. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    ok Sir

    Great!!!

    Blessing
     
  15. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    My SM102-5P machine is keep "beeping" but the water grease is sufficient/at max mark. Sometimes off the machine and start again next day, the beeping sound is deactivated, but it beep again after few hours running. Can you know what is the issue? Thank you and appreciate your comment.
     

    Attached Files:

  16. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    (SM102-5P) And, one of my printing unit valve is working another way.
    When its supposed to be ON the valve turn OFF. When its supposed to be OFF the valve turn ON.
    But for the rest of printing units are work fine, only 1 is work in other way.
    Quite a strange problem, hope master here can guide.
     

    Attached Files:

  17. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Please explain what led up to this problem. Press just installed? Repair or troubleshooting caused issue?
     
  18. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    Regarding this issue (1):-
    My SM102-5P machine is keep "beeping" but the water grease is sufficient/at max mark. Sometimes off the machine and start again next day, the beeping sound is deactivated, but it beep again after few hours running. Can you know what is the issue? Thank you and appreciate your comment.
    >> The screen display attached (IMG_5593)

    Regarding this issue (2):-
    (SM102-5P) And, one of my printing unit valve is working another way.
    >> This without any error message.
     

    Attached Files:

  19. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    (1). We must know revolution count, cannot read numbers.
    (2). As I’d mentioned, please tell us when this pneumatic impression ram began operating in reverse sequence. Has the press been installed recently? Did you, or a mechanic, work on the assembly recently?
     

  20. KhorWK

    KhorWK Member

    Joined:
    Apr 2021
    Messages:
    46
    Location:
    Malaysia
    1) Not so sure what is revolution count, will check again and see.
    2) No, the machine in running all the while but suddenly 1 of the printing unit valve like this.
     
Loading...