Sheet delivery

Discussion in 'Heidelberg Printing Presses' started by PrintEdge, Apr 23, 2020.

  1. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    Guys I would appreciate any help with my GTO 52/4 always leaves 2 sheets in delivery end without completing cycle to exit. Supposed to deliver 9 sheets when I stop production, only delivers 7 with 2 still in press.
     
  2. Mathew

    Mathew Senior Member

    Joined:
    Apr 2010
    Messages:
    530
    Location:
    Kolding-Denmark
    What is the age of your press?
     
  3. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    I bet I know what you're thinking, Matthew! I'll refrain from answering him, but as we say here in the States, "I'm chomping at the bit" wanting to direct him to the issue :).
     
  4. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    I’m not at work right now, but I’m thinking like year 1998
     
  5. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    Me too, I’m at a loss. Looked for timing disk and etc. haven’t located one yet.
     
  6. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Timing disc? No. Impression sequencing roller switches mounted on brackets surrounding a cam on each impression cylinder. Look for wear at pivoting lever and excessive play of roller on the spindle. There must be one, possibly more, worn out switches which control the impression sequencing.
     
  7. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    It doesn’t have to be in impression, just running set up sheets on idol same response.
     
  8. precision1984

    precision1984 Member

    Joined:
    Oct 2010
    Messages:
    26
    Location:
    plymouth, mn
    Is the press clearing the feedboard, not leaving a sheet at the headstops?
     
  9. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    All sheets are clearing the feed board, no miss feeds, just doesn’t deliver all the sheets. ALWAYS leaves 2 in delivery end. 1 in chain grippers 1 in #4 tower at impression cylinder grippers.
     
  10. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    GTO multicolor presses should always be leaving a sheet at the headstops, I believe you have a front barrier issue. Do your headstops continue to sweep and raise while idling? Are you getting an intermittent hammering noise upon trip off? Is the barrier solenoid functioning?
     
  11. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    I’ve ran this press since new install, it has never left a sheet at head stops. The head stops used to continue to sweep, the shop owner had a contractor work on it and when he left the head stops don’t sweep idling but now it continues to leave 2 sheets in press. This contractor was in about a year ago. I am at a loss why shop owner didn’t make sure he fixed the 2 sheet issue. As far as the barrier solenoid if it’s the solenoid under the feed table to the right it does operate. I know there is an adjustable rod connecting there. You think maybe the contractor didn’t adjust it appropriately?
     
  12. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    "New install" as in new from factory? Or pre-owned machine? You say about '98...so it's the DDS dampener type machine?
     
  13. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Could be that the operating rod you mentioned isn't adjusted properly, but keep in mind the many components in the whole barrier assembly depend on each other for quite a number of functions...don't change the operating rod length with the thought it will remedy the issue. Sounds like you need service.
     
  14. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    This machine was a NEW Heidelberg U.S.A. install. It is with the DDS dampeners. The solenoid that operates the head stops and all that connects with it is what this guy installed. Im thinking he missadjusted it. Got an idea what the specs may be?
     
  15. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Intimately. However, the "specs" are just a recommended starting point for each adjustment, and each adjustment point directly affects another, more so on an older machine, from wear of moving components Simply put, without a degree wheel, arbor and cylinder flag, ya'll are, with all due respect, pissing in the wind.
     
    MRTYMM likes this.
  16. PrintEdge

    PrintEdge Member

    Joined:
    Apr 2020
    Messages:
    12
    Location:
    Tennessee
    Thanks Junker1984, I was hoping it could have been a relay or such that could’ve been causing this issue.
     
  17. member 18943

    member 18943 Previous User

    Joined:
    Nov 2017
    Messages:
    0
    Hello,
    There is a timer inside the control cabinet.
    You can adjust it very easy.
     
  18. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    A timer, Maher? Could you explain? Since this is a '98 model with some electronics I may not be familiar with, I may have been giving out bad info. But during my career, if the GTO presses left sheets in the machine and no sheet on the feedboard it was typically a barrier issue. I humbly await your reply, as I'm sure the original poster. :-(
     
  19. member 18943

    member 18943 Previous User

    Joined:
    Nov 2017
    Messages:
    0
    In GTO machines, there are three yellow timers in the cabinet (one for forward inch, one for backward inch and the third one is for stopping the machine after last sheet leave the feeder)
    As you know, there is no IDS in GTO machines, so you have to adjust the time to stop the machine after triggering the missing sheet sensor (it is the same time the lasr sheet leave the feeder) , this time depends on how many printing units in the machine.
     

  20. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Thank you, Maher. If you have a schematic for this model year, would you list the timer designation for the poster?
     
Loading...