GTO V/F 52-4colores error INIT test 7

Discussion in 'Heidelberg Printing Presses' started by Ronald mecatron, Jul 2, 2019.

  1. Ronald mecatron

    Ronald mecatron Member

    Joined:
    Jul 2019
    Messages:
    7
    Location:
    Perú
    Water motors, suction belt motor and sheet ejection motor do not work. I found the SPM card fuse damaged, but by changing it, the fault persists. In the CPtronic when I turn on the machine, I get the error FFF5 HAK-01 from test 7 of INIT
    A favor I need to know if the SPM card would be the problem.
     

    Attached Files:

  2. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    According to fault codes, it appears you may have a fault in an LTK. "HAK discovered that the voltage which is necessary for code detection is missing".
     
  3. Ronald mecatron

    Ronald mecatron Member

    Joined:
    Jul 2019
    Messages:
    7
    Location:
    Perú
    The voltage between +, T 12V +, - 20V apparently the motors of pile in and out are good if they answer the problem is with the motors of water, strip of suction and the one that accommodates the pliegos in exit. The green LED on the MSK card does not turn on permanently
     
  4. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Ah! Guess I may have gotten my wires crossed. (A little light humor).
     
  5. Ronald mecatron

    Ronald mecatron Member

    Joined:
    Jul 2019
    Messages:
    7
    Location:
    Perú
    A favor I need your support to find the problem of the machine
     
  6. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Software version?
     
  7. CHOCK

    CHOCK Senior Member

    Joined:
    Dec 2016
    Messages:
    2,852
    Location:
    Managua,Nicaragua
    Hi sir:
    As my colleague say: 1) You have problem in HAK and LT ; the motor voltage is NOT receiving the voltage appropiated.
    2) Normally you must test the fuse. When the fuse is blown in power supply the motor does Not turn anymore and the corresponding Red diode is Lit.
    3) Not problem with with SPM board.
    4) Test the Leds: Red+Yellow in ltk.
     
  8. Ronald mecatron

    Ronald mecatron Member

    Joined:
    Jul 2019
    Messages:
    7
    Location:
    Perú
    In the LTK there are only 2 red LEDs lit in the sources the green LEDs are on
     
  9. junker1984

    junker1984 Senior Member

    Joined:
    Jan 2010
    Messages:
    1,031
    Location:
    US, Midwest
    Have you reset the LTKs, meaning unplug and plug back in?
     
  10. Ronald mecatron

    Ronald mecatron Member

    Joined:
    Jul 2019
    Messages:
    7
    Location:
    Perú
    Solved the problem of the water engines of 2,3, and 4, but the fault is still in the body 1
     
  11. Ronald mecatron

    Ronald mecatron Member

    Joined:
    Jul 2019
    Messages:
    7
    Location:
    Perú
    E AK2_11 does not work the body water motor 1
     

    Attached Files:

  12. Mathew

    Mathew Senior Member

    Joined:
    Apr 2010
    Messages:
    530
    Location:
    Kolding-Denmark
    Hi fellows,
    In general, HAK FFF5 indicates disconnected auxiliary drive. As I can consider from the photo, it should be Shhet slow down drive at delivery. But it's very important to know what was the latest condition before this problem appeared.
    Regarding second photo, I assume variant codes are not correct. Can you send some photos from variant codes or compare them with reference sheet if available?

    Good luck
     
  13. Ronald mecatron

    Ronald mecatron Member

    Joined:
    Jul 2019
    Messages:
    7
    Location:
    Perú
    I have another problem with the main engine. When it starts to start it stops and the next error comes out DIN test 1
    HWI 7F7F

    What can be the solution?
     

    Attached Files:


  14. Mathew

    Mathew Senior Member

    Joined:
    Apr 2010
    Messages:
    530
    Location:
    Kolding-Denmark
    This error indicates "No HWI pulses received" by ESK/REK.
    You didn't send us software version and variant codes.
     
Loading...