Recent Content by ryobiTech

  1. ryobiTech
    Post

    Ryobi 512 "paper feed break"

    Hi, Check those two grub screws on the outer collar. And also check the three bolts which lock the feeder drive to the main press
    Post by: ryobiTech, Apr 20, 2023 in forum: Ryobi Printing Presses
  2. ryobiTech
    Post

    ryobi 3200 np ink duck roller

    Hi, Did you get this sorted?
    Post by: ryobiTech, Oct 12, 2022 in forum: Ryobi Printing Presses
  3. ryobiTech
    Post

    Duplo 5000 touch screen software

    What's your email address?
    Post by: ryobiTech, Jan 17, 2020 in forum: Collator-Booklet Maker Systems
  4. ryobiTech
    Thread

    T 18 error on EBA 721?

    Does anyone know what T 18 error is on an EBA 721?
    Thread by: ryobiTech, Dec 4, 2019, 0 replies, in forum: Cutters and Trimmers
  5. ryobiTech
    Post

    Duplo 5000 touch screen software

    Did you get this sorted?
    Post by: ryobiTech, Jul 17, 2019 in forum: Collator-Booklet Maker Systems
  6. ryobiTech
    Post

    Ryobi 920 delivery table wont go down whilst in production

    Have you power at the motor when the sensor is activated?
    Post by: ryobiTech, Jul 17, 2019 in forum: Ryobi Printing Presses
  7. ryobiTech
    Post

    RYOBI 925 register on the 1st unit moves on its own from left to right

    Either end play in the cylinder or the servo motor is creaping.
    Post by: ryobiTech, Jul 17, 2019 in forum: Ryobi Printing Presses
  8. ryobiTech
    Post

    3302 vertical adjustment

    It needs to be lubricated. Theres a greese nipple on the side of the blanket cylinder gear.
    Post by: ryobiTech, Jul 17, 2019 in forum: Ryobi Printing Presses
  9. ryobiTech
    Post

    DUPLO 5000 DC10/60

    Check the Diode on the upper part of the sensor, This can have a flat spot from paper wear causing light defraction.
    Post by: ryobiTech, Jul 10, 2018 in forum: Collator-Booklet Maker Systems
  10. ryobiTech
    Post

    Vertical registration adjustment o n ryobi 3304H

    There is a greese nipple located on the gear close to the scale, pump lots of greese in there and work the adjustment, it will free up eventually.
    Post by: ryobiTech, Jun 26, 2018 in forum: Ryobi Printing Presses
  11. ryobiTech
    Post

    Tresu

    I dont know these units but my guess is a faulty thermostat/thermister or the cooler motor relay is stuck.
    Post by: ryobiTech, Feb 15, 2018 in forum: Komori Printing Presses
  12. ryobiTech
    Post

    Polar 66 BRK-4096 Error

    I will look at the manual tomorrow and let you know the test for the PCB.
    Post by: ryobiTech, Feb 15, 2018 in forum: Cutters and Trimmers
  13. ryobiTech
    Post

    Polar 66 BRK-4096 Error

    Edit, Just read your last message, Could be a faulty encoder, the encoder looks for a certain amount of pulses within a given timeframe. If these...
    Post by: ryobiTech, Feb 15, 2018 in forum: Cutters and Trimmers
  14. ryobiTech
    Post

    Polar 66 BRK-4096 Error

    Hi, I usually set up the sensor so I can put a .2mm guage between the flag and sensor. About the thickness of 200gsm card. The encoder is at the...
    Post by: ryobiTech, Feb 14, 2018 in forum: Cutters and Trimmers