Recent content by iGentleman

  1. Transfer/Detack Shield Fault XPE-09-3061

    I'm with CargoPantsMan on this one. I always lower my transfer setting for transfer A & B in the media subsystem attributes for the offending paper. Sometimes I have to crank it down pretty far but it always seems to work. Angle - Hey man! What's up? Seen any bats lately? lol!
  2. Xerox iGen 150 error code XPE-10-3112

    For S&G's, here is the "official definition" and initial actions: XPE-10-3112 Fuser AC Line Voltage Out of Range in Print 2FSC PWB (the FSC printed wire board on Panel 11A Area) declared that the AC Voltage is out of range in Print (above 254VAC or below 179VAC). Initial Actions NOTE: The Step...
  3. PDF preflight

    Ask your Xerox analyst for the "JobPrepGuide Version3." Gives you suggested settings for InDesign, Quark and PDF's as well as preflighting.
  4. reposition output Igen4

    "Reposition Output" used to allow you to tell the the machine to go back and restart or "Reposition Output" from certain page within a currently running job. Lets say you were printing a long run of a variable job and noticed and IQ defect. The idea would be that you could pause the machine/job...
  5. stumped..color registration problems

    Call the hotline and check to see if you are on the latest and greatest software for your hardware type. Also, as for the color/IQ issues before, it has been recommended that if you only run at 175 LPI that you do the whole color maintenance routine for 200 LPI at least once a moth. This will...
  6. iGen4 with FreeFlow: Faulting on PDF with Bitmap jobs

    Legacy PS or APPE que? Any imposition applied? FreeFlow Software level?
  7. speed/size question

    I believe so since a 45 cm (17.7165 in here) sheet size in the process direction runs at a pitch rate of 5. Do you have the Large Paper Productivity license? iGen4 only I think. That could boost # of sheets per min in certain sizes.
  8. speed/size question

    iGen3/4 or iGen150?
  9. speed/size question

    Here are some handouts for both the iGen150 and iGen4 which have very different print speeds. CargoPantsMan - FYI -Using the Periodicity of Photoreceptor Belt Artifacts (table 16. pitch rate) is fine for troubleshooting IQ, however it is misleading for calculating print speed on an iGen150...
  10. IGEN 3 End of support, all machines.

    I doubt they will stop. They still sell toner for the Docutech line and they stopped selling them long ago.
  11. IGEN 3 End of support, all machines.

    You could get trained as an "operator technician" with Xerox XPP training for iGen3.
  12. Press Fault XPE-03-4007

    You can check this: The XPE-03-4007 code is displayed if there is a loss of communication by the MOB Interface PWB. The XPE-03-5007 code is displayed if the MOB Interface PWB was reset unexpectedly. This could be caused by one of the following: •Intermittent Figure 24P552/J1 connector at the...
  13. Decurler Optimization

    From the Operators Guide iGen4 FFPS ADJ 13 Decurler Adjustment Purpose The purpose of this procedure is to adjust the output curl from the decurler subsystem. If the amount of curl in the paper is causing a stacking performance problem or a factor in paper jams, perform the adjustment...
  14. Rub-off on silk-coated stock

    Who makes the paper and what is its weight in GSM?
  15. Color matching!!!

    Although there are some very specific things you can do, ultimately it will depend on what you are trying to match. A hard copy proof? A known color space? A spot color? More specifics are in order. Baring that, knowing what's in the file as well as the color workflow of your RIP (Creo Fiery...
Back
Top