Recent content by iGenTech

You can vacuum the developer out of the trickle tube from the top. Then feed a 10 gage wire down the tube to brake up any thing that is stuck. The wire should all the way to the waste bottle. As far as other causes of spitting or streaking not listed before. There is a trimmer bar for the mag...

RMigen, The last time I seen this problem it was a bad new fuser roll. The circumference of the roll was to small which was slowing down the paper causing the prefuser to over drive and bow up the stock. The weight of the stock was not the problem and 8.5x11 ran just fine. It wasn't until I...

Sunshine, Paper motion on most printers is based on fixed RPMs 50/60hz of the paper path motors. On most there is a master clock we call machine clock that's the speed of the photo belt. On the igen 4. From the time a page is feed to the time it is stacked it is under the control of...

Stiv, :-) it's never the stock.... FYI you can remove the belt stripper finger assy. It's one of those things I wish I had came up with. No printer needs it and someone is making a crap load selling them.

Stiv, I would be shocked if the scratches were from the p/r stripper fingers. I have seen the bottom plastic clip brake that latches it close but still almost impossible to scratch the belt. Mostlikly one of these twisted 8 wire mods, dicor grids, tab assy, cleaner blade or brush, stock perfs...

Peels, Just make a shim. Say 5 inches wide and 1 1/2 inches thick, place it on the stacker cart about 4 inches from the right side. Also make sure the reg belts are not smooth or worn out.

The down fall of Xerox. Diagnostics and over priced Parts and Supplies... CRocket, Don't hold your breath looking for third party igen service. There is no one in third party ISO's for the igen. You wont see third party service on the Igens due to the cost of parts, supplies, xerox...

drlew, Igen3 start at $5,000 and go up. I just see 2 sell on eBay 2 feeders 2 stackers both with the finest front end the freeflow x86 and both were under $9,000 and under 8mil images. It's the cost of service parts training and software license that's the killer of the igens and xerox for...

drlew, I know of 10+ igen3's. Email the specs you are looking for. Ie.type of frontend Creo, fiery, Free Flow, number of stackers, feeders or finishing. Who will be maintaining the igen Xerox, third party, or do you need service training? The price of an igen depends on several factors...

XPE-10-3346 and XPE-10-3341 XPE-10-3346 and XPE-10-3341 Decurler Entrance/Exit missing +36vdc I havent checked to see where the +36vdc goes through. It might be that it goes through the Output front door switiches. Cheat them to see if it fixes it, ie missaligned door. or a switch maybe...

Xpe-09-3066 RMiGen, XPE-09-3066 Is Transfer/Detack PS Overtemperature or Wire Current Fault Transfer/Detack Wire wire current is out of range indictive of a broke wire or Arc. I would start by cleaning or replacing T and D Dicors. Is this the only fault listed? You could be missing 24vdc...

Email me and I'll send you the install specs. Igentech@yahoo.com

Meesh48 , I know I already answered this in wiki but reposting sense it was moved here. XPE-09-3167, indicates that during dC0951, the Center ETAC high target could not be determined. Check the following DC131 NVM value: Station4EtacTimingSetupCorrection loc 14155. If the value is not less...

Hi, Thy are used in the Xerox DC 242/252, 260, iGen3, other Rip's. Thanks

Well I fourth that papapascucci with the add detail..... dC0610 (IOP) Image On Paper: Registration Setup is used to adjust the image squareness, magnification (IB-to-OB and LE-to-TE), registration (IB-to-OB and LE-to-TE), and paper skew for both simplex and duplex printing. If your...