Recent Content by Bert van Gompel

  1. Bert van Gompel
    Post

    Polar 150 CE problems with hydraulics

    which pump is causing problems the hydraulic circuit consists of 2 parts. 1 section for the coupling and 1 part for the pressure bar
    Post by: Bert van Gompel, Aug 8, 2024 in forum: Cutters and Trimmers
  2. Bert van Gompel
    Post

    Trying to find spare parts Senator 092 E-Line

    We can supply this printed circuit board, but what is the problem?
    Post by: Bert van Gompel, Mar 23, 2024 in forum: Cutters and Trimmers
  3. Bert van Gompel
    Thread

    Como Large format Heavy Duty Paper Cutter Machine 220cm /86"

    For sale Como Large format Heavy Duty Paper Cutter Machine 220cm /86" Year 1987 Dual Gearbox Drive Double Arm Pull Microcut Computer Hydraulic...
    Thread by: Bert van Gompel, Jan 12, 2024, 0 replies, in forum: Finishing Equipment for sale
  4. Bert van Gompel
    Post

    Wohlenberg MCS 3 positioning error

    Mr. Johannes, Can you explain how you did this Do you have a diagram with a description of the parts you used? I am having the same problem with...
    Post by: Bert van Gompel, Sep 24, 2023 in forum: Cutters and Trimmers
  5. Bert van Gompel
    Post

    Wohlenberg 115 Cut tec stopping abruptly after cut

    It is that the machine runs too far and then triggers S64 I would start by degreasing the clutch and adjust it to approx. 0.35mm
    Post by: Bert van Gompel, Jun 26, 2023 in forum: Cutters and Trimmers
  6. Bert van Gompel
    Post

    Polar 92 EM

    The problem is that the blade delay is switched on and you have to turn it back until the red led is off. it is the rotary knob with the green...
    Post by: Bert van Gompel, May 22, 2023 in forum: Cutters and Trimmers
  7. Bert van Gompel
    Post

    Schneider Senator 78 e-line guillotine mainboard

    Hello We can supply any printed circuit board for Schneider Senator Machines. Can you send me a picture of this printed circuit board and the...
    Post by: Bert van Gompel, Mar 21, 2023 in forum: Cutters and Trimmers
  8. Bert van Gompel
    Post

    Polar 92E

    Press bar pressure may be too high for the material you are cutting. There are 2 different shear bolts there is one with a drilled hole in the...
    Post by: Bert van Gompel, Mar 14, 2023 in forum: Cutters and Trimmers
  9. Bert van Gompel
    Post

    Problem tb sprint 315

    the machine has probably been without power for a while and the battery of the PLC has gone flat Some parameters have to be re-entered The best...
    Post by: Bert van Gompel, Aug 18, 2022 in forum: Collator-Booklet Maker Systems
  10. Bert van Gompel
    Post

    MCS-2

    This is a software setting that depends on the size of the machine. what is the size and exact type of the machine?
    Post by: Bert van Gompel, Jul 19, 2021 in forum: Cutters and Trimmers
  11. Bert van Gompel
    Thread

    Wohlenberg MCS 1984 PB platine defect

    Hi all, We have a Wohlenberg MCS system '85 of year 1984 It has a defect PB Platine, is there someone that has an electrical diagram of this...
    Thread by: Bert van Gompel, May 12, 2021, 1 replies, in forum: Cutters and Trimmers
  12. Bert van Gompel
    Post

    Polar 150 CE problems with hydraulics

    Bert van Gompel Van Gompel Grafische Machines b.v. Tuinstraat 6 5531 GK Bladel The Netherlands Tel. + 31 (0) 497 382 269 Mob.+ 31 (0)654 722 356...
    Post by: Bert van Gompel, Jul 28, 2020 in forum: Cutters and Trimmers
  13. Bert van Gompel
    Post

    Polar 150 CE problems with hydraulics

    The above mentioned parts are all good the machine still works before we disassemble the valve We opened the valve because the clamp no longer...
    Post by: Bert van Gompel, Jul 28, 2020 in forum: Cutters and Trimmers