Hi guys I am now facing Feeder ON problem in SM52 Compect two color machine. In inching, Feeder is

Discussion in 'Heidelberg Printing Presses' started by Rashid Hussain, Oct 9, 2021.

  1. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    Hi guys
    I am now facing Feeder ON problem in SM52 Compect two color machine.
    In inching, Feeder is working but when Run the machine and try to start the feeder for paper run then its not working, also feedr ON push button light not glow.
    No double sheet error.
    Both units damping motors are running.
    Delivery table is in up position.
    Replaced the both units EWK board.
    At 45° double sheet detector sensor value is 577.
    No errors in dyn and int tests.
    Primary and secondary safties on display shows no safety.
    Replaced the Encoder with zero position seting.
    Is any one faced the this kind of problem then please share your remedy or any suggestion.
    Regards
     
    Last edited: Oct 9, 2021
  2. Steve F

    Steve F Member

    Joined:
    Jun 2013
    Messages:
    45
    Location:
    Scotland
    Although the delivery table is up, if you've got a dodgy micro-switch, the press would display that the table is down and therefore disable the paper run button.
    Worth a quick check.

    Steve
     
  3. ashok kumar

    ashok kumar Senior Member

    Joined:
    Nov 2017
    Messages:
    224
    Location:
    india
    Hi
    Check and confirm
    1) no error is flashing (g30.... )
    2) delivery pile position in display( error menu/delivery menu/
    3) check output configuration that clutch (bit is 1 in I/O list)

    If possible then sahre vdo
     
  4. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    Thanks for reply but i couldn't see any error in feeder or delivery side.
    As per your said what is the positon of dodgy micro switch and its work?
    If its active then is it show any thing in delivery safety manu.
     
  5. Steve F

    Steve F Member

    Joined:
    Jun 2013
    Messages:
    45
    Location:
    Scotland
    If a micro-switch is faulty, the display/console will show delivery main pile at bottom, even though it's raised.
    It won't show up as a fault.
     
  6. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    But in my case delivery table condition is normal and display didn't showing the table is at bottom.
     
  7. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    hello check the black sensor see or the doe head.
     
  8. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    Which black sensor ?
    You mean double sheet sensor or any other sensor ????
    Please explain it and position.
    Regards
     
  9. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    there is a black rectangle shaped sensor that makes the table go up automatically!
     
  10. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    Go up or down by this sensor?
     
  11. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    sent an picture so that I can surely see that we do not understand each other thank you very much.
     
  12. asem alsafady

    asem alsafady Senior Member

    Joined:
    Mar 2016
    Messages:
    179
    Location:
    Amman Jordan
    Check your grease system as well, it may need reset.
     
  13. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
     

    Attached Files:

  14. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    Warning safety manu display shots
     

    Attached Files:

  15. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    Dyn test
     

    Attached Files:

  16. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    hello dear sir, if it is the feeder which does not start see if the lubrication at the margin on the drive side has not become soluble. check see the sensor if it works well.Thanks to you
     

    Attached Files:

  17. Rashid Hussain

    Rashid Hussain Member

    Joined:
    Jun 2019
    Messages:
    11
    Location:
    Karachi-Pakistan
    Thanks for advice, Lubrication is ok and sensor is working well.
    Feeder pile sensor will check and let you know.
     

  18. Beguin

    Beguin Senior Member

    Joined:
    Jan 2020
    Messages:
    348
    Location:
    Côté d'ivoire
    Also check this sensor to see if there is one on your machine.
    on the feeder head, the receiving stack is low or high?
     

    Attached Files: