roland 300 feeder problem

dear friends we are installing a man roland 300 4 col + coater, as we had finished the installation when we start the machine all the functions are working except functions in the feeder. eg: feeder pile up and down, suction head up and down, nothing is working in the feeder. even if i trip the circuit breaker of feeder pile i cannot see the message in the monitor. but i can see the input signal reaching control cabin when we pressing the buttons. but there is no output in the control cabin. any one please help me in this issue - thankyou

 

Hello Vijay78

you may try this,put the delivery&feeder plate to the floor make sure there is slack
in the cable or chains,then go to your console and plug in the makeready & working positions. if that doesn't work you may have to use the format button on the feeder.Also check to see that all sensors on the feeder are clean.
Hope this helps

LUCKY-N-KY

 

Feeder problem R300

Have you tried to use the hand held terminal to see if you get any response?
When you say: no output signal, do you mean from the output PCB's or do you mean that nothing happens at the contactor level?

www.controlgraphicsusa.com

 

thankyou very much for your kind suggessions sir, finally the problem had been solved by god's grace ... the make ready was not done ... that was the problem ... thank you very much once again.

 

thankyou very much for your kind suggessions sir, finally the problem had been solved by god's grace ... the make ready was not done ... that was the problem ... thank you very much once again.

 

hi hello.vijay78 do u have Man Rolland machine please send me your mail Id ot send send a hi to kotaon@gmail.com

 

hi hello.vijay78 do u install Man Rolland machine please send me ur email id mobile no. or send me hi on kotaon@gmail.com
deepak 9829038608

 

I have the same problem in my machine
How can I do make ready to fix this
thanks
hello.vijay78

 

Hi sir:
Hope you are well
1) open the operator manual feeder A+B, and look for Loose wires, tight very well, and clean with Cleaner contacts spray.

2) look for the sensors:B024+025+026+090+091, Clean it and look for loose wires, and tight it very well.and test it

3) look for the main motor in Feeder M-004 and see if is running when you touch the Push button Feeder? See at the terminals of M-004 if the Voltages : 220Vca or 380Vca or 440Vca or Whatever voltages you are using is the terminal of motor, when you push the button.

4) If is NOT running, see the Fuses or Circuit breaker and Reset,

5)Previously see if the fuses or c.breaker are o.k in the power supply, and replace, repair or Reset: fuses or circuit breaker

 

connect with handterminal to feeder and check state of all POS motors...

 

Hi sir:
do the same steps as i did indicated before
Hope you are well
1) open the operator manual feeder A+B, and look for Loose wires, tight very well, and clean with Cleaner contacts spray.

2) look for the sensors:B024+025+026+090+091, Clean it and look for loose wires, and tight it very well.and test it

3) look for the main motor in Feeder M-004 and see if is running when you touch the Push button Feeder? See at the terminals of M-004 if the Voltages : 220Vca or 380Vca or 440Vca or Whatever voltages you are using is the terminal of motor, when you push the button.

4) If is NOT running, see the Fuses or Circuit breaker and Reset,

5)Previously see if the fuses or c.breaker are o.k in the power supply, and replace, repair or Reset: fuses or circuit breaker


Finally, use your schematic diagrams.

 

Good Morning My Friends
I have a problem in feeder mail pile table
after I start the machine i can move the pile up and down slowly
when the pile become at distance 120 mm from floor it stop (No rise & No fall)
can you help me to fix the

 

You can move pile only slow? When pile is in let say middle position?
Please write down serie of macnine... Problem can be in program switch or in sensor B081...

 

Hi sir:
Did you do the steps that i did mentioned before??
1) open the operator manual feeder A+B, and look for Loose wires, tight very well, and clean with Cleaner contacts spray.

2) look for the sensors:B024+025+026+090+091, Clean it and look for loose wires, and tight it very well.and test it

3) look for the main motor in Feeder M-004 and see if is running when you touch the Push button Feeder? See at the terminals of M-004 if the Voltages : 220Vca or 380Vca or 440Vca or Whatever voltages you are using is the terminal of motor, when you push the button.

4) If is NOT running, see the Fuses or Circuit breaker and Reset,

5)Previously see if the fuses or c.breaker are o.k in the power supply, and replace, repair or Reset: fuses or circuit breaker


Finally, use your schematic diagrams.