deletions on 80lb gloss text

Discussion in 'Xerox iGen3, iGen4, & iGen5 Digital Presses' started by Swifty2, Aug 7, 2013.

  1. Swifty2

    Swifty2 Senior Member

    Joined:
    Mar 2013
    Messages:
    300
    Location:
    Ma.
    oh what fun today:mad:
    fuser contact is set at 14.5 , PR belt is ok as deletions are random. fuser roll Looks fine,pressure roll is only a couple weeks old. All sensors and paper paths cleaned. The stock is fresh out of the case, have tried two brands that have run good in the past ,heaters in feeder trays are off.......... service call placed
     
    Swifty2, Aug 7, 2013
    #1
  2. peels

    peels tree killer :)

    Joined:
    Dec 2010
    Messages:
    1,113
    Location:
    southeast iowa, usa
    If it is a long, semi thin crooked deletion(kinda looks like its supposed to be there)....

    I bet you find the paper "wrinkling" as it hits the PR belt, leaving a valley that doesnt transfer. bypass the front lower door, and watch it run, you'll see it happen.

    just went through this. completely random, blamed on paper getting too hot and too much moisture.
     
    peels, Aug 7, 2013
    #2
  3. peels

    peels tree killer :)

    Joined:
    Dec 2010
    Messages:
    1,113
    Location:
    southeast iowa, usa
    peels, Aug 7, 2013
    #3
  4. CAignop

    CAignop Member

    Joined:
    Aug 2013
    Messages:
    10
    Location:
    orange county,CA
    new to forum....i always saw this problem with certain brands..we just keep away from them..i thinks its moisture in paper.
     
    CAignop, Aug 7, 2013
    #4
  5. Swifty2

    Swifty2 Senior Member

    Joined:
    Mar 2013
    Messages:
    300
    Location:
    Ma.
    phone base support ...blames the heaters in tray...even when I tell them that they are off LOL. Tech blames the stock.
    Yes Peels,the deletions are similar(ours are smaller,on the lead edge ,and it is consistently in the same area of the sheet ..We have ordered another brand of stock as a smaller size is not an option
     
    Swifty2, Aug 7, 2013
    #5
  6. CAignop

    CAignop Member

    Joined:
    Aug 2013
    Messages:
    10
    Location:
    orange county,CA
    swifty what brand do you use the most?
     
    CAignop, Aug 7, 2013
    #6
  7. Swifty2

    Swifty2 Senior Member

    Joined:
    Mar 2013
    Messages:
    300
    Location:
    Ma.
    New Page futura has always worked....
    We will order xerox brand...then they can not blame the paper!! LOL
     
    Swifty2, Aug 7, 2013
    #7
  8. Swifty2

    Swifty2 Senior Member

    Joined:
    Mar 2013
    Messages:
    300
    Location:
    Ma.
    xerox stock ran perfect
    I am able to get the futura to run using enhanced image but the copy quality sux.......that tells us that the speed/timeing/buckle needs to be adjusted for that particular stock... it can be done by the operator
     
    Swifty2, Aug 8, 2013
    #8
  9. LeeB

    LeeB Senior Member

    Joined:
    Jul 2012
    Messages:
    105
    Location:
    OZ
    You can go into the stock and adjust the transfer properties as well. I suggest building a separate stock in your library and playing with the transfer settings there that particular stock so you dont hose up your library setting on the stock that does run good. I have resolved a few "Snow" artifacts this way.
     
    LeeB, Aug 9, 2013
    #9

  11. Swifty2

    Swifty2 Senior Member

    Joined:
    Mar 2013
    Messages:
    300
    Location:
    Ma.
    We have just tried Ariva paper.....the sheet looks wrinkled out of the box....RAN LIKE A CHAMP go figure LMAOF
     
    Swifty2, Aug 15, 2013
    #10
Loading...
Similar Threads
  1. peels

    Deletions!!!!!!

    peels, Jun 27, 2013, in forum: Xerox iGen3, iGen4, & iGen5 Digital Presses
    Replies:
    8
    Views:
    2,599
    peels
    Jun 4, 2014