Polar 76 EM - error 92 -

Discussion in 'Cutters and Trimmers' started by GTOZP, May 1, 2015.

  1. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    Hello, my Polar 76 EM gives me the error -92- (security bold magnet)
    we checked the magnet switch at the rear and the HK card
    there is also a kind of "burning smell" in the left area of the cards
    where the little ventilator is placed
    perhaps a electrical part on a second card is gone?
    does someone have a clue which card also has to deal with this security bolt / magnet
    thank you.........
     
  2. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    Das sieht man auf dem Schaltplan
    This is shown on the electrical diagrams.
    Das Signal B.SBE wird durch die Karte HK ausgewertet
    The Signal B.SBE is controlled by the board HK
    Das Signal B.SBA wird durch die Karten HK und IAR ausgewertet.
    The Signal B.SBE is controlled by the boards HK and IAR
    Die Spule Y.SB wird durch die Karte HK aktiviert.
    The coil Y.SB is activated by the board HK
    Coloured paper
     
  3. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    Der Pressbalken kommt auch nicht automatisch runter, oder ist
    das normal wenn zuvor der Sicherheitsbolzen nicht ausrückt?

    the clamp does not automaticly press down, or is this o.k.
    if the security bolt does not move...
     
  4. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    Right, first function should be the lowering of the clamp.

    Testing step by step and using the LED’s on the board HK
    Simultaneously activating of both cut buttons LED 6 and 7 off / LED 8 and 9 on
    Enabling of next step LED V14 on
    Light barrier test LED V12 short time off
    Light barrier test accepted LED V18 on
    Activating the clamp LED V17 on
    The clamp is lowering
    Safety bolt activation LED V16 on
    Feedback from safety bolt LED V4 off and LED V5 on
    And so on, and so on.

    Does the foot pedal work?

    Richtig, zuerst muss der Pressbalken abgesenkt werden.

    Schritt für Schritt mit den LED’s auf der Karte HK prüfen
    Gleichzeitige Betätigung der Schneidtasten LED 6 und 7 aus / LED 8 und 9 an
    Freigabe für nächsten Schritt LED V14 an
    Lichtschrankentest LED V12 kurze Zeit aus
    Lichtschrankentest akzeptiert LED V18 an
    Aktivierung der Pressung LED V17 an
    Der Pressbalken wird abgesenkt
    Aktivierung des Sicherheitsbolzens LED V16 an
    Rückmeldung vom Sicherheitsbolzen LED V4 aus und LED V5 an
    Und so weiter, und so weiter.

    Funktioniert das Fußpedal?

    Coloured paper
     
  5. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    die Maschine hat keine Lichtschranke, es ist die 76EM mit 9 Programmen ca. Bj 84
    - Maschine an, Referenzpunkt angefahren: LED 4 (?) + 6 +7 an
    - Schneidtasten drücken: LED 8 + 9 an
    - es erscheint Fehler -92-

    ich weiss nicht ob es damit was zu tun hat, manchmal hat sie sich in der letzten Zeit auch beim anfahren eines programmierten Schnittes vertan und dann gepiept und geblinkt
    -- bist du ein freier Techniker in Deutschland ?? --

    machine doesn't have an light barrier, 9 programms, bulit in 1984
    - maschine on, LED 4 + 6 + 7 on
    - pressing cut buttoms, LED 8 + 9 on
    - error -92-
    in the last time the machine sometimes gets a wrong programmed messure
    than there was the beeping noise and blinking display
     
  6. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    The problem regarding wrong positioning is something totally different and is not related to the cutting circuit.
    With or without light barrier the LED’s are reacting in the same way.
    Is the LED V17 active? And it would good to know if the food pedal is working.
    I am asking because the next step would be following the output signals.
    Do you have the electrical drawings for this machine?
    I am not a freelancer

    Das Problem mit der falschen Positionierung ist etwas ganz anderes und hat nichts mit dem Schneidkreis zu tun.
    Mito der ohne Lichtschranke, die LED’s reagieren gleich.
    Ist die LED V17 aktiv? Und es wäre gut zu wissen ob das Fußpedal funktioniert.
    Ich frage weil der nächste Schritt wahrscheinlich die Kontrolle der Ausgangssignale sein wird.
    Hast Du die Schaltpläne für die Maschine?
    Ich bin kein freier Servicetechniker

    Coloured paper
     
  7. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    zuerst mal vielen Dank für die Antworten
    nein, es leuchtet keine weitere LED
    wie soll ich das Fußpedal prüfen?
    die Schaltpläne habe ich....

    no there is no other LED on
    how should I test the foot pedal
    yes, circuit plans are here......
     
  8. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    Checking the foot pedal is easy just use the foot pedal instead of cutting.
    It looks like you need a service engineer
    Where are you located?

    Das Fußpedal prüfen ist einfach. Anstelle zu Schneiden einfach auf das Pedal treten.
    Es sieht aber so aus als ob Du einen Servicetechniker brauchst.
    Wo wohnst Du?

    Coloured paper
     
  9. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    wenn ich auf das Pedal trete passiert nix, der Pressbalken kommt runter wie immer
    ich sitze in Nordbayern, bei Würzburg

    the footpedal makes the normal function, the clamp is coming down
     
  10. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    This is maybe at least one good news.
    Does the machine have an air cushion function for the table?
    And if yes, does the air cushion works?
    I am asking because it is possible you have no more 42V d. c.
    This would not explain the crazy situation with the LED’s, but it is a chance
    The service from Heidelberg is not so cheap.

    Vielleicht ist zumindest das eine gute Nachricht
    Hat die Maschinen einen Lufttisch?
    Und wenn ja, funktioniert die Tischluft?
    Ich frage weil es möglich sein kann, dass Du keine +42 V hast.
    Das würde zwar nicht die kreative Situation mit den LED’s erklären aber es ist eine Chance.
    Der Service von Heidelberg ist ja auch nicht so billig.
     
  11. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    Lufttisch läuft problemlos... wie gesagt etwas "schmorrt"
    auf einer Leiterplatte.... ich habe noch eine 78E stehen
    aber davon wird man keine Karte zum testen nehmen können?
    die Maschine brauche ich aber als Backup... sonst wird es eng

    air cushion table is working fine,
    there is a smell of something burned on one of the cards
    I have another 78E, maybe I can take one of the cards of it
    for testing?
     
  12. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    I misunderstood the last information from you.
    If the food pedal works you have 42V d.c.
    It looks like you need some spare parts and a service engineer.

    Ich habe den letzten Eintrag falsch verstanden.
    Wenn das Fußpedal funktioniert hast DU auch +42V
    Es sieht wirklich so als ob Du Ersatzteile und einen Servicetechniker brauchst.
     
  13. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    ok.... vielen Dank
    thank you.....
     
  14. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    The boards from the 78E are different.
    Sorry, I would call for help.

    Good luck
    Coloured paper

    Die Karten von einer 78e sind total anders.
    Sorry, ich würde den Service anrufen.

    Viel Glück
    Coloured paper
     
  15. GTOZP

    GTOZP Member

    Joined:
    May 2015
    Messages:
    8
    Location:
    Germany
    dieser Widerstand auf der HK-Karte (Bild anbei) wird verdammt heiss und "schmaucht"
    mein Elektroniker weiss nicht warum... ich habe auch mal die Magnetspule
    des Sicherheitsbolzens abgekemmt, weil er meinte daß vielleicht die Spule
    defekt und dadurch zuviel Strom gezogen wird, aber das war es auch nicht
    er hat schon versch. Teile auf der Karte erneuert u.a. diesen Widerstand
    daher das Lötzinn

    this resistor placed on the HK-card gets too hot and we don't know why
    I disconnected the safety magnet because we thought it is damaged and there
    is too much voltage, but thats not the fault
     

    Attached Files:

  16. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    Yes, if the HK is broken two components have to be replaced together.
    Replacing of components on electronic board for paper cutters is illegal and forbidden. And in Germany for sure.

    Ja, wenn die Karte HK defekt ist werden zusammen zwei Bauteile ausgetauscht.
    Das Reparieren von elektronischen Karten von Papierschneidemaschinen ist illegal und verboten. Und in Deutschland ganz sicher
    Coloured paper
     
  17. kumartanz

    kumartanz New Member

    Joined:
    May 2015
    Messages:
    1
    Location:
    tanzania
    hi there,

    we have recently purchased the Polar 76 EM, we are looking for the service manual if anyone could help with it, TIA....
    regards

    Kumar
     
  18. Coloured paper

    Coloured paper Senior Member

    Joined:
    Oct 2012
    Messages:
    258
    Location:
    Germany
    Hi Kumar!

    Polar never made a service manual for 76 machines.
    What is your problem?

    Coloured paper
     
  19. simon yeung

    simon yeung Member

    Joined:
    Jul 2012
    Messages:
    23
    Location:
    hong kong

  20. Transcopies

    Transcopies New Member

    Joined:
    Jan 2024
    Messages:
    1
    Location:
    Canada
    I know it's been 8 years but we had the same problem with our Polar 76 EM. Thank you so much for pointing out the C16. It worked! :)
     
Loading...